Material Hatch: Choosing and Drawing One That Reads at Scale.

A material hatch is a code the reader decodes in half a second. Here is how to pick the right pattern, set its scale and weight, and keep it legible on the sheet.
What a hatch is for: coding, not decoration
A material hatch is a coding system. It tells the reader what the cutting plane has passed through, or what surface they are looking at, using a convention they already know. In section, it separates cut material from everything beyond. In plan and elevation, it distinguishes one finish from the next. That is its entire job.
Decide which of those jobs a hatch is doing before you choose a pattern. The question to ask is not "what looks good?" but "what is the reader trying to find out?" In a wall section the answer is usually "what is this layer, and how thick is it?" In an elevation it is "where does the brick stop and the render start?" In a site plan it might be "what is hard, what is soft?" Each question calls for a different amount of information.
Compare two drawings. On a competition board, the sheet may have to carry the whole technical argument for a scheme in a few sections and no accompanying report. There the hatch does heavy lifting: it shows the timber frame, the insulation, the cast concrete, the earth bank. The reader has seconds, and the hatch is the fastest route to "this building is made of these things." On a planning elevation, the same brick façade needs far less. A light tone and a few courses of linework near the corners tell the planning officer it is brick. Fill the whole elevation with dense hatching and you bury the window reveals and the shadow lines that the drawing is actually there to show.
Standardised symbols are preferred because readers recognise them across offices and disciplines. A structural engineer, a quantity surveyor and a planning officer should all read your concrete as concrete without checking a key. That shared recognition is the reason hatches work at all.
Keep a hatch only if it answers a question the reader would otherwise ask: what is cut, which layer is this, what finish is shown. If it answers none of them, remove it.
Matching pattern to material the way readers expect
Architects read certain marks on sight. The common references associate diagonal or cross-hatched lines with masonry, stipple or aggregate marks with concrete, scalloped or zig-zag lines with batt insulation, parallel grain lines with timber, and irregular dots or short marks with earth. These conventions vary between standards, so consistency across a drawing set and a legend on the sheet matter more than any claim to one universal pattern.
| Material | Typical hatch convention | What the reader should take from it |
|---|---|---|
| Brick, block masonry | Diagonal or cross-hatched lines | Solid, coursed material |
| Concrete | Stipple, aggregate marks | Cast, mass material |
| Insulation (batt) | Scalloped or zig-zag line | A soft, thick layer of build-up |
| Timber | Parallel grain lines | Structural or finish timber |
| Earth, fill | Irregular dots or short marks | Ground, not construction |
### The wall build-up test
A typical cavity wall in section is the best test of whether your hatches work. Work from outside in: outer masonry leaf, cavity, insulation, inner leaf. The reader needs to tell four layers apart in a strip of drawing perhaps 20 mm wide on paper. Each layer needs a different pattern, and no two neighbouring layers should look alike. If the outer leaf and the inner leaf both carry the same diagonal hatch with only a cavity between them, the section reads as one thick wall with a gap in it. Give the inner leaf a different material treatment, say concrete block shown with stipple, and the build-up reads correctly.
The cavity itself usually takes no hatch at all. White space is a legitimate symbol, and an empty cavity next to a patterned insulation layer is more legible than any attempt to fill both.
### One convention, held across the set
Where offices and standards disagree, pick one convention and hold it across every drawing in the set. A reader who finds timber shown with grain lines on drawing 03 and diagonal lines on drawing 07 will assume the second is a different material. A sheet legend resolves any doubt, and it costs a few square centimetres of paper.
### Custom patterns: presentation only
Custom patterns for specific stones, tiles or proprietary products have a place on presentation sheets, where recognisable material character helps tell the story of a scheme. On a technical drawing they cost clarity. Standard symbols communicate faster in technical documentation, and a contractor reading a detail should not have to decode a bespoke pattern to find out what is being built.
Choose one hatch convention per project, put it in a legend, and never let two adjacent layers share a pattern.
Scale, spacing and line weight: where hatches go wrong
Scale is the main failure point. Hatch spacing is set in paper millimetres, so a pattern that reads cleanly at 1:20 collapses into a dark grey block at 1:100. The lines are the same distance apart on paper, but the drawing now covers five times as much building in the same space, so every element is smaller and the hatch has nothing left to hold against. Guidance repeatedly stresses matching hatch density to drawing scale, and the fix is to re-set the pattern for each drawing scale rather than inheriting it from a detail library.
Common architectural scales run 1:100 or 1:50 for general plans, sections and elevations, and 1:20, 1:10, 1:5 or 1:2 for details. One architectural drawing guide suggests poché at 1:100 to 1:200, true hatching at 1:20 and larger, and a mixture at 1:50. Treat that as a sound starting point rather than a fixed law.
### The same brick, two scales
Put the same brick wall on one sheet at 1:50 and at 1:5 and the right treatments differ sharply. At 1:5 you have room for a coarse, explicit brick pattern, courses drawn at a pitch you can read and perhaps the mortar joint shown. At 1:50 the same pattern would clot, so you simplify: a light tone, a sparse diagonal hatch, or a solid fill. The wall is the same wall. What the reader needs from it has changed, because at 1:50 they are asking "where is the masonry?" and at 1:5 they are asking "how is it built?"
### Keep hatch lines subordinate
Cut edges must dominate, with the hatch indicating what lies inside them. Public CAD standards bear this out: one lists 0.18 mm for material indications and hatch lines against 0.50 mm for cut lines and profiles, and another similarly places hatching at 0.18 mm and section cuts at 0.50 to 0.70 mm. As a working habit, keep hatch lines two to three pen weights lighter than the cut line. That is a practical office convention rather than a formal requirement, but the principle underneath it is well supported: if the hatch is as heavy as the profile, the outline of the section disappears into texture.
### Check the output, not the screen
The relevant test is the plotted or viewed output, not the zoomed-in authoring view. A hatch that looks elegant at 400% on your monitor may be an unreadable smear on an A3 planning PDF. Check legibility at the size the sheet will be read:
- A1 pin-up: viewed from a metre or two, so very fine hatching vanishes and weight differences matter most.
- A3 in a Design and Access Statement: read close up, but the drawing is reduced, so a dense hatch may close up.
- Phone-sized PDF in a client's inbox: the harshest test. If the layers still separate here, they will separate anywhere.
Re-set hatch spacing for every drawing scale, keep it two to three weights lighter than the cut line, and judge it at the size the sheet will actually be read.
Hatch versus solid fill versus tone
Hatch, poché and tone serve different reading tasks, and choosing the wrong one is a more common mistake than choosing a poor pattern. **Solid poché** prioritises mass and figure-ground clarity. It suits a diagrammatic section or a general-arrangement plan, where the reader wants to grasp the shape of the building's solid and void before anything else. In a competition plan, black poché on the walls lets the circulation and room sequence read at a glance, and no hatch could do that job as fast. **Pattern hatch** suits technical sections and details, where the reader must tell construction layers apart. Poché cannot do this, since a solid black wall hides the build-up that a detail exists to show. **Tonal fill** suits planning and presentation drawings where the linework underneath must keep reading through the colour. A light grey wash over a site plan, or a pale tint behind a landscape area, adds information without burying the lines that define the edges. This is a drawing-communication choice rather than a universal standard, but it is a reliable one. ### Mix them deliberately The best drawings use all three, each for a reason. In a single section you might use black poché for the structural frame, a light hatch for the finishes and linings, and nothing at all for glazing. The result reads in layers of importance: structure first, finish second, openings as absence. Every treatment is doing a different job, so none of them competes with the others. The failure mode is using one treatment everywhere out of habit, either hatching every surface until the sheet is grey or poché-ing everything until the build-up is lost. Pick per element, not per drawing.A hatch is a question answered before the reader asks it. Match poché, pattern and tone to the question each part of the drawing has to answer, and cut everything else.
Drawing and fixing hatches in Vector and Linea
Vector and Linea are two lanes of the same ArchAdemia Tools suite, and both give you proper control over hatch work, from drawing a hatch to cleaning one up. ### In Linea: hatch as a managed layer Linea's 2D drafting tools include a Hatch tool, working alongside Line, Polyline, Rectangle, Circle, Arc, Text, Leader and Revision cloud. Hatch settings include fill type, pattern, scale and angle, and hatches can appear in plans, sections, elevations and callouts, exporting with views to PDF and DWG or DXF. Those are the documented capabilities; test them against your own drawing before relying on them for a live job. Hatches sit on member-named layers, each with its own colour, weight and linetype. Any kind of drafting object can go on a layer, and a layer can be hidden or set not to plot. That structure supports the habit that matters most. ### Layer discipline is the habit that matters most Put hatches on their own layer. The documentation recommends a dedicated hatch layer, and the reason is practical. With hatches isolated:- You can set the hatch layer to a fine weight in one place, which keeps hatch lines subordinate to cut lines across the whole drawing.
- You can hide the layer when a sheet needs a quiet version, for example a planning elevation that wants outline only.
- You can set it not to plot when the hatch is only a working aid, such as a temporary marker while you coordinate a build-up.
- When the drawing leaves for a consultant's CAD package, the hatch is already separated from the geometry it describes.
Keep reading.
Try ArchAdemia Tools for yourself
Draw it, model it, render it, publish it. One place, built for architects and small practices. From £19 a month, all in.


