Adding views to a sheet

Place several views on one sheet, each linked to the model with its own position, title and scale. A view sits on one sheet.

To copy a whole sheet and its drawings, right-click the sheet and choose Duplicate, then Duplicate with Views. Each viewport uses a new duplicate view with its own detailing. Site and location copies appear under Site in the Views browser and keep their own crop and building display choice. The original sheet and its views stay in place.

A linked building keeps its door and window tags in its own building views. Site plans and location plans carry dimensions and setting-out instead. Red opening bodies use red outlines without solid red fills, on the sheet and in exports as well as on the canvas.

  1. In Sheet view, open the Views tab at the top of the tray.
  2. Drag a view's name onto the page. It lands where you let go, and its box fills.
  3. Or click its hollow box to place it on the current page. With no pointer to aim by, it lands in the largest free area of the drawing area, clear of the views already there and the title block.
  4. Select the placed drawing. The View settings card sets its Scale and View title, and Show view title hides or shows the caption under it.

A view lands at its own scale, on free paper if it fits. A drag keeps the point you let go at. A hollow box, a legend, a camera, a render or a register has no pointer, so it goes in the largest free area of the drawing area, at its top-left, with a small gap from the views already placed and their captions, and always inside the drawing area, so never over the title block. If nothing is big enough it takes the largest free area anyway and stays selected, so you can move it. A page with no free paper at all takes it at the top-left. A drawing bigger than the paper starts at the top-left of the drawing area. When its first capture appears, it may move to free paper, but its scale never changes.

Drag a placed view anywhere on the page: it goes where you let go, over the title block or past the paper's edge if you take it there, and the arrow keys carry it just as far. Guides offer an alignment only when you are close to one, a few millimetres away, and never hold the view. Hold Shift while you drag to switch snapping off for that drag.

A view you place takes the sheet's set scale unless the view already has a scale of its own. When the sheet's scale is Automatic and the view has none, the view takes the largest scale in the table at which it fits the paper. Change a sheet's set scale with Default scale on the Page card; views already on the sheet keep theirs. A site or location plan takes it only at its own default scale or coarser. Reset crop in the View settings card works in two steps. If you have trimmed the view on the sheet, the first press clears that trim and brings the box back onto the paper, and the view keeps its own crop. A drawing too big for the paper at its scale sits centred on the paper and prints clipped to the plan area, and a note says the whole view is larger than the paper; drag the crop edges to choose what shows. With no trim left, the next press clears the view's own crop, shows the whole view again, and re-sizes its box about the same centre, moved back onto the paper where it fits. It is off for a view that is not cropped.

Floor plans, ceiling plans, foundation plans, roof plans, the Site plan and Location plan, sections, elevations, Callouts and saved orthographic views (under 3D Views) can all go on a sheet, and so can 3D diagrams, cameras, renders and schedules, below. A plain click on a name still opens that view. The Views tab lists the drawing you are in: a site slot offers its site plan, site sections, street scenes and callouts, and a building slot its plans, elevations and sections, each for the sheets of that same slot. A saved orthographic view under 3D Views has Drawing settings beneath its name: set Drawing scale, use Fit crop to drawing, then edit the crop's Left, Right, Top and Bottom extents, or Clear crop to show the full drawing; the boxes of the sheets showing that view are re-sized, and if the drawing cannot be measured they keep their size and you are told. A view has one scale: a drawing placed on a sheet uses it, and changing the Scale in the sheet tray changes the view itself. Different views can have different scales. A callout without its own scale follows its owning plan, section, elevation or callout at one step finer; changing another plan of the same level leaves it alone.

Each plan, section, elevation and callout is its own drawing on a sheet. A duplicate of the Ground Floor (a fire plan, say) goes on a sheet of its own while the original stays where it was, because a view sits on one sheet and the two are different views. Open the source row's menu and choose Duplicate view for a plan, or Duplicate for a section, elevation or callout. Choose Duplicate with detailing to copy its owned annotations too. Rename the copy, then drag it onto its own sheet. Neither command copies an existing sheet placement. A placed plan's Drawing card has a Drawing picker that lists every plan view by name, with Site plan and Location plan; picking another switches which plan the box shows, and a view already on a sheet is refused with the sheet's name. Deleting a plan view takes its place on the sheet with it.

A cropped view is drawn through its two crops. The model is cut at the model crop and the annotation, the dimensions, tags, symbols, notes and level markers, at the dashed annotation crop around it; an annotation the annotation crop cuts is left off the sheet. The view's box on the page covers the annotation crop. With Crop annotations off in the view's properties, the box grows to take in whatever the annotation draws. A plan view with a crop follows the same rule. A plan with no crop has a box that takes in its annotation too, so a door or window tag standing clear of its wall is drawn whole.

3D diagrams, cameras, renders and schedules

A 3D diagram (under 3D Views) goes on a sheet like any view and draws as vector, the same drawing the Diagram view shows, so it prints sharp and exports with the sheet. Drag a camera from 3D Views instead and Linea makes a diagram from that camera and places it; the camera's box then shows that diagram. Drop the same camera again and it reuses the diagram, so the one-sheet rule stops the second.

A render under Renderings lands as a picture where you drop it. A schedule under Schedules lands as a table; see Schedules. Neither has a scale, and the title block's Scale cell ignores them.

One view, one sheet

As in Revit, a view sits on one sheet. A render is a view too. Every view in the Views tab carries a small box: filled when the view is on a sheet, hollow when it is not. Hover a filled box to see which sheet; click it to open that sheet with the drawing selected. Try to place a view that is already on a sheet and you are told which one, with a button to open it. Need the same drawing on another sheet? Duplicate the view and place that copy. A callout is another view of its own when you want a cropped detail. Legends are the exception: a legend can sit on as many sheets as you like.

Under Sheets at the foot of the Views tab, open a sheet to list what is on it. Clicking one of those opens its sheet with that drawing selected.

View template

Each placed drawing has a View template select in its View settings card, next to Scale. Pick one of your templates and every setting it includes is taken from it, not from the view the drawing shows: Scale and Phase show the template's value, unavailable, and hovering names the template, and the drawing itself is drawn with the template's detail level, depth cue, services, annotation and Visibility/Graphics settings. A setting the template does not include follows the view as before. Editing the template redraws every placed drawing that uses it. Pick None and the drawing's own values come back. To set many placed drawings from a template at once without assigning it, use Apply to views... in the View templates window. A placed drawing takes the included scale and phase filter only; its other settings belong to the view it shows.

Moving, resizing and aligning

Drag a placed drawing to move it. Guides appear as it nears the page centre, the margins, or another drawing's edges and centres, and it snaps to them. They are dashed: blue for another drawing, red for the sheet itself, green for the building's ground line and levels. When its gap to one drawing would equal the gap between two others, or the gaps either side of it would match, a measuring line with a tick at each end appears on every matching gap, including each further gap of the same size along the row and it snaps to that spacing. Hold Shift to move freely. Drag a corner handle to resize and the drawing keeps its proportions exactly, even when it meets the page edge or its smallest size; the edge handles stretch one side.

Select a single drawing and the View settings card carries Align left, Align centre, Align right, Align top, Align middle and Align bottom, then Bring to front, Send to back and Remove from sheet. The drawing area is the space inside the margins and title block, not the whole paper. Select several drawings and the same six buttons line them up with each other: they align to the edges and centres of the selection as a whole, so drawings side by side stay side by side on Align left, in a single undo step. A cropped or scaled drawing lines up by the part that shows, and a drawing with its title hidden by the drawing alone. A selected drawing shows a blue outline on the sheet, and Crop view trims how much of it shows without changing its scale or position. While you crop, the window's edges and handles trim it and the view itself stays put: a press inside the window does nothing, and neither do the arrow keys. Done cropping lets you move it again.

Select a scale bar on the page and the View settings card shows its Scale: pick a fixed scale, or Follow view to read the view it sits with; the card names that view. With several views on the sheet and none selected, the menu lists Follow and each view's name after the fixed scales; Follow view is unavailable only on a sheet with no view. A north arrow, image, tag, detail line or view reference gets a card that names what is selected.

Phase

Each placed drawing can show its own phase. The View settings card's Phase filter takes Follow drawing, Show all, Existing + new, Demolition or New only. Show all shows everything, Existing + new shows existing and new work with demolished work hidden, Demolition shows existing and demolished work, and New only shows new work. Follow drawing is the default: it follows the source view's own filter where set, otherwise the drawing-wide Phases shown setting from the Display dropdown in the menu bar, and keeps following it when you change it. A site plan starts with Existing + new unless you choose another filter. The viewport's own choice wins over its source view's.

Scale

On a sheet with several views, each label has its own number, view title and scale. A number stays with its view when you bring it forward or send it back. Deleting a view leaves its number free, and the next view takes the lowest free number without renumbering the others. When all scaled drawings share a scale, the title block shows it. When two or more true scales differ, it reads As indicated: read each view label for its scale. A fitted view is labelled Not to scale and never claims a ratio. A schedule has no scale. A new view starts on clear paper where possible without moving the views already placed. Once placed, a view stays where you put it when its preview finishes loading; you can still drag views over each other and use the alignment guides.

Scale offers Fit to region and a list. The metric list is 1:5, 1:10, 1:20, 1:50, 1:100, 1:200, 1:500, 1:1000, 1:1250 and 1:2500. The imperial list runs from 1" = 1'-0" down to 1" = 200'. A site plan offers 1:200 and 1:500, and a location plan 1:1250 and 1:2500; a new site plan opens at 1:500 and a new location plan at 1:1250. Sections and street scenes can use any of them, so a site section or a street scene can sit at 1:200 or 1:500 too. Plan sources also get a Drawing select: Floor plan, Foundation plan, Roof plan, Site plan or Location plan.

A site plan or location plan also gets a Buildings select, which sets how every building and every placed building type on it is drawn: as a Ground plan (the ground level of each building, with a light grey tint under it so the site doesn't show through, kept to the outer faces of the walls), as a Roof plan (the eaves outline with its ridges, hips and valleys), or as an Outline (one closed silhouette of the walls' outer faces in the heavy cut line). A site plan starts on Roof plan and a location plan on Outline. Everything else on a site plan draws in black and white until you give it a material, apart from trees. The choice belongs to that drawing on the sheet, so a sheet keeps what you set it to, and a DWG or DXF export writes each building type once as a block with one insert for every plot that uses it. What each building shows (room labels, room fills, furniture, dimensions) is set per view in the Outliner's Site plan display group, and the sheet, the PDF and the DWG or DXF follow it: room labels start off. Door and window tags stay in the building slot's own views and do not appear on a site plan or location plan, on paper or in exports.

A floor plan's DWG or DXF export keeps a ramp's outline, slope arrow and gradient label together on A-FLOR-RAMP. Freezing that layer hides the whole ramp symbol.

Use Rotate view to turn a plan for the sheet. The turn is saved with the view, so the placed drawing, its PDF and its DWG carry it, its north arrow follows, and upright text stays upright. A second view of the same level keeps its own turn.

A site plan with a great deal on it (large patterned areas, a lot of linework and symbols) is drawn with a coarser pattern pitch so it fits, and the drawing's card says so. If no pitch is coarse enough, the drawing shows This site plan has too much detail to draw on a sheet: hide a drafting layer, or place it at a smaller scale.

Street scenes and site sections cut and draw every placed building type where its plot puts it. A handed plot is cut as the mirror image of its partner, so a section through a plain plot and a handed one shows the two walls on opposite sides.

A drawing keeps the scale it was given and shows its whole crop region at that scale. Moving or resizing its box does not shrink the crop window. If the crop runs off the paper, it is clipped at the paper's edge, the card adds a plain note, Runs off the paper at 1:50., and the title block still reads 1:50. The same note appears when a tag, a dimension or a note drawn in the margin beside the crop reaches 5 mm or more past the page edge. Change the paper size or orientation, or pick another scale, when you want it to fit; Fit to region is the one choice that sizes a drawing to its box, and it is marked Not to scale. When two drawings overlap, whichever is later in the stacking order prints on top. Drag the view or its move handle freely around the sheet. Its box centre snaps horizontally to the centre of the drawing area left of the title block, and vertically to the sheet centre; a guide shows while snapped. Drag the view title separately to bring it closer to the contents. Its position moves with the view, survives reopening and prints in the PDF; each drag is one undo.