Drawing the terrain perimeter

The terrain perimeter is the outline of the ground you're modelling. You draw and edit it the same way as a floor's outline.

In sketch Select, Ctrl-click adds an edge, Shift-click adds one or takes it out and Alt-click takes it out. Drag left to right for edges wholly inside the box, or right to left for edges it touches, in plan or 3D. You can also click a corner to select it on its own, with the same keys, or draw a box left to right round one; Delete removes selected corners. Move, Rotate, Scale, Mirror and Flip work on the selected edges or corners, and the edges meeting a selected corner follow it. The outline stays open until you finish or cancel it.

The perimeter and its drawing guides stay on the site ground even when a moved or turned building was selected before you began.

These tools are in a site slot, and in a drawing that is not filed in a project. A building slot has no terrain, plot, road or planting tools; its Site row reads Import site slot and links the building to a site slot in its project.

  1. A new site opens the Site row on Sculpt; after that, each site keeps the last tab you used in it other than Plan. On Sculpt, click Draw terrain perimeter. Once you've drawn one it reads Edit terrain perimeter. The Site area button on the Plan tab opens the same sketch. The perimeter is one loop: draw a new closed outline beside the old one and it replaces it when you finish, with Cancel keeping the old one. Neighbouring buildings, trees and roads you imported are never deleted by a perimeter change. To mark a red line round one plot, use Boundary line instead.
  2. While you edit, the outline shows in pink. On a new site it starts blank with Line armed; once you have a perimeter it opens with that outline ready to edit.
  3. Draw with Line, Rectangle or Arc from the bottom toolbar. While you draw a line, type a length and press Enter to place it exactly, or Tab to type an angle.
  4. If you've imported an OS map or a survey (DWG or DXF), use Pick lines instead of tracing: in the site plan, hover a line and it lights up, then click to add it. On a polyline a click adds the one segment under the pointer; hold Shift and click to add the whole polyline, so a proposal boundary drawn as one closed polyline becomes the outline in a single click. A curved line comes in as an arc. On a site fetched from OpenStreetMap, the building footprints can be picked too, and so can the edges of water and green areas; Shift takes a footprint's whole outline. Lines on hidden layers can't be picked; lines on locked layers can, because picking only reads them. Picking the same line twice adds it once. Picked lines are ordinary pink segments, so Trim, Split, Join at corner and Offset work on them. Pick lines is in the site plan only; the 3D view doesn't offer it.
  5. With Select, click an edge to pick it, then drag it, nudge it with the arrow keys, or press Delete to remove it. Drag a box on empty canvas to pick several edges at once: drag left to right to take the edges wholly inside the box, right to left to take every edge it touches, and hold Shift to add to what's picked. Delete removes all of them, including the last one: an empty sketch is fine while you work, and the tick stays unavailable until there is a closed outline again. A picked edge shows its length, its distance to the nearest parallel edge and the overall size of the outline measured along and across it, in the site plan and in 3D, while you draw as well as once the outline is closed. Click the distance to the parallel edge, or the overall size across the edge, and type a new value to move the edge; it is one undo step.
  6. New points snap to the outline's own corners and midpoints as you draw, and to imported linework: its corners, midpoints, crossings and the line itself, on any visible layer, and to the corners of fetched OpenStreetMap buildings. Site sketches also catch the walls, floor outlines and linework of placed houses at their positions on the site. When an endpoint marker appears, click to join that existing corner exactly. When an alignment guide appears, the point lands exactly on that alignment; move clear of it and the guide releases. Snapping back to the first corner closes the loop in plan or 3D, including over sloping terrain.
  7. When dragging a pink edge in the site plan or in 3D, the move snaps along red or green, or parallel to the edge's original direction. Hold Shift to keep the inferred direction, and release it to move freely again. Type a Distance and press Enter to move that far along the direction shown.
  8. Offset uses the same controls as drafting: type a distance and press Enter, choose Move to replace the edge or Copy to keep it, then hover and click the ghost on your cursor's side. Hold Shift for the whole polyline. The tool stays armed and remembers the distance and choice for the session; see Offsetting linework. Trim, Split and Join at corner tidy the corners where edges meet.
  9. Click the tick to save the perimeter, or the cross to discard your changes. Saving is one undo step.

The red line boundary

When the planning red line is the edge of your terrain, turn on Red line boundary under Draw terrain perimeter in the Site row. The perimeter then draws as a heavy red line on the site and location plans, on sheets and in DWG or DXF (on the SITE-BOUNDARY layer), and the row reports the Application site area.

The red line is often not the terrain edge. In that case draw it in Boundary mode on the site plan's bar, with Application site ticked; see The site plan toolbar. A closed Red line you have drawn is the application site, and the switch says so and is ignored while it stands.

The sketch stays open until you tick or cross it, so clicking around the drawing never closes it. Before you have placed a point, one Escape cancels it, and Enter closes the loop when it has an area or says why it cannot. The tick needs a closed outline that doesn't cross itself. If a new outline sits clear of the existing ground, a dialog warns that finishing replaces the perimeter. Once a perimeter is saved, Create terrain builds the ground inside it. Once saved, the outline is a dark line on the ground (white on a dark scene). Click it, in the site plan or in 3D, or pick Terrain Perimeter in the outliner, to select it: it turns blue, with chevrons on its edges to pull them and a grip to move the whole outline.