Roofs

Draw the footprint, finish it, and Linea builds the roof over it. Pitch, overhang and eaves set the shape.

Escape leaves the drawing sub-step and keeps every placed outline edge. Pressing Escape again keeps this sketch open too. Before you have placed anything, one Escape cancels the sketch. Use the green tick to finish the action, or its cross to discard it. This also applies while using Edit perimeter or Edit profile. If you are editing a typed value, its first Escape clears the field.

You can change view part way through. Go between 2D, 3D and Split as often as you like: every placed line stays where it is, the tool stays armed, and Cancel and Finish stay on the toolbar. Click the next point in the view you've moved to and the footprint carries on from the last one, on the same level, and it still finishes as one Undo.

To change a placed roof's pitch, select the roof and use Angle in the roof's Dimensions section. It changes every mass and every slope that follows it, while keeping individual overrides. While you are still drawing, the same setting is Angle in Parameters.

To change one slope of a gable, hip or lean-to, select the roof and use Pitch on its compass-named slope row under Segments. Click the number to type an angle, or drag it. The other slopes keep their own pitches and meet along one joined ridge; an asymmetric gable moves its ridge to where the slopes meet. Angle changes the slopes that follow the roof-wide value while keeping gable ends and the lean-to's high edge in place. When a slope or finish has been overridden, Reset overrides appears under Dimensions; choose it to return all slopes to the roof-wide pitch and finishes. One Undo restores the whole edit, and Escape cancels a drag.

Draw a second roof so that it overlaps the first on the same storey with its eaves at the same height, and the two are joined as you finish drawing (two roofs with eaves at different heights, a hidden roof or one inside a hidden group or level, or roofs in different phases are left apart): each keeps what shows from outside, and they meet along a valley. A section through a joined pair is cut as one roof with a single outline; where the two roofs carry different coverings, each covering has its own fill and a line follows the valley between them. Adding a segment to a selected roof does not join anything. Unjoin roofs in the right-click menu separates them again. Switching an outline roof to Gable in the segment row rebuilds it as the same gable wings a drawn Gable gives, on an L, a T or a U.

In a building section, an elevation or a callout (drawn from a plan, a section or an elevation), Roof and Roof features keep the current view open. A roof footprint follows the drawing plane, which in a callout over a plan is the plan itself. Rooflights, dormers, chimneys, cupolas, solar panels and surface vents attach to the roof face you point at. Fascia, bargeboard, gutter, soffit and ridge vent attach to their roof edge; a downpipe attaches to its gutter. The preview marks the placement the click creates.

Select the roof and open Structural items in its panel to add trusses, rafters or purlins linked to the roof. On a roof of several masses, the Courtyards and structure on row above them names which mass they belong to. Set their centres, member size, set-out end and offset from the build-up's structural plane. They follow the roof's shape, edits and Base level. Copying the roof includes them. Deleting the roof removes its structure straight away; one Undo restores them together. See Columns, beams and trusses for the controls.

Overhang is measured horizontally in plan from the picked wall's outer face, at eaves and verges alike. Changing the pitch keeps that horizontal distance. For a sketched roof, the footprint stays where you drew it and the overhang extends horizontally from that outline. In plan the roof's outline is its eave: the wall line moved out by the overhang, or by half the wall's thickness where the eave is flush. That outline is what plan snaps land on.

A flat roof that meets a wall on its own level standing taller than the roof stops at that wall's inner face, so the overhang never runs on into the wall or out past it. That holds whether you drew the roof to the wall's centreline, its outer face or its inner face, and however the wall's top is set (a height, or a level plus an offset). Raise or lower the wall, or change its thickness or position, and the roof rebuilds to match without you touching the roof. So does changing the height of the level the wall's top comes from, or placing a floor above that shortens the wall; the roof follows the top the wall is drawn to, including a roof grouped with other objects.

Each edge can have an overhang of its own. Open an edge's row in the panel, beside its Edge pitch, and its Overhang slider (0 to 3 m) sets that edge alone; the plan outline stops where the 3D cut does. Set an edge's pitch to 0 and it becomes a flat end: it keeps its row and its Overhang, takes no slope finish, and gives the slope back as soon as you give it a pitch again.

Select a roof and four chevrons stand clear of its sides. Drag one to move the whole roof along that side's axis; they only move the roof, and its size and shape stay with the panel and Edit perimeter. A fifth chevron over the ridge lifts or lowers the roof, either side of its level, and snaps so a roof can drop onto a wall top. That height is the roof's Base offset, which also has a row in Dimensions.

Select a roof and open Face finishes in Parameters. Under Exterior, Show in 3D controls the model finish. The Tiles, Soffit, Fascia and Rainwater goods swatches choose materials from the Library. Rainwater goods sets the gutters and downpipes separately. Auto returns the roof-wide row to white and clears hand paint from the boards or goods it controls. Individual segment and slope overrides stay until you choose Reset overrides.

Show in 2D controls the drawn finish. Leave Match 3D on to use the material colours, or turn it off to choose separate drawing colours for each row. Set the surface pattern and its colour below. A pattern you choose follows the visible roof surfaces in plan, elevation and section. With several roofs selected, a row whose finish differs between them reads Varies, and choosing one sets it on all of them in one undo step.

Each roof segment follows its roof's finish until you change it. Open a segment's row under Segments in the roof's panel and its Face finishes section shows what it inherits; set a pattern, a colour or a background there and only that segment changes, and Use the roof's finish puts it back. At a valley each face takes the finish of its own segment, in elevation, in section and in plan.

In plan a roof seen from above (a roof plan, or a cut plane raised above the eaves) draws its finish on the roof surface. Where two segments meet, the join sits on the valley line, where one surface rises above the other. A roof the cut plane passes through keeps its cut drawing. A roof drawn on the storey directly below can be clicked on the plan of the storey above, where the cut passes through it, and on that storey's roof plan; so can its dormers and rooflights. Where the storey's own floors and rooms sit over the roof, they take the click: click the roof where it is clear of them. A click keeps you on the storey you are viewing, and a roof or dormer picked there drags as it does on its own storey: a dormer stays on its roof, and each move is one undo step.

A roof whose type has tiles or slates as its outer layer draws a coursing hatch with no pattern to set: lines along the eaves, one batten gauge apart up the slope, and joints staggered by the width of a tile. Plain tiles are set out at 100 mm gauge and 165 mm wide, slates at 200 mm gauge and 250 mm wide. In elevation the courses lie in the roof's own plane, so they foreshorten with the pitch; in plan, on a roof seen from above, each slope draws its own, spaced by the gauge as the pitch shortens it on the ground. A metal, membrane or green covering draws none, and a pattern you set on the roof, or turning Show in 2D off, takes over from it.

A small house in 3D with a gable roof over it and the gable ends closed up to the ridge.
A gable roof over a house, with the gable ends closed to the ridge.

Changing a placed roof between Overhang and Flush, hidden gutter keeps its attached walls following it. Changing the overhang, gutter or roof shape does the same while the roof still bears on the wall lines. A wall attached to the roof is cut to its underside, and so is any door or window in that wall that crosses the roof line: the frame and glass follow the slope, in 3D, section and elevation. Linea tells you once, in a message, when a door or window comes to cross the roof, and it does not repeat it on reopening the model. One that sits wholly above the roof line is not drawn until you lower it or raise the roof.

Walls attached under a polygon roof follow its underside along their whole length, including at an inward corner and on diagonal walls. The wall has a closed top face, and windows keep their openings below the roof cut. This also applies on upper storeys and when the roof is turned. In plan, Coarse and Fine show the same polygon outline and its real hips, ridges and valleys, with each valley drawn once. In section, a roof type with layers shows those layers at the cut, following the slopes.

Where a roof with layers bears on a wall, each layer ends at its own place at the eave, in 3D as in section: the covering runs out to the drip, the structure ends at the fascia, the insulation stops at the outer face of the wall's insulation, and the vapour control layer and lining stop at the wall's inner face. Remove the wall and the layers end on the roof's own edge again.

To draw a roof

A roof footprint can follow a curtain wall's outer frame face and end corners in plan. In 3D, approach the frame's top edge or top corners to catch them. This works on the level you are drawing on, including upper storeys; the curtain wall's grid remains available for setting out.

  1. Click Roof on the Build toolbar.
  2. In Parameters, pick a roof type and a shape: Gable, Hip, Lean-to, Flat, Gambrel or Mansard. The roof panel offers the same six.
  3. Set Angle (0 to 85°) and Overhang. Switch on Custom eaves height to reveal an Eave slider (1 to 6 m).
  4. For a roof that stops on the wall, choose Flush, hidden gutter for the eave. A roof made with Pick wall keeps its gutter seated in those walls when you switch the eave. The gutter sits in the wall's thickness, behind its outer leaf, and the roof ends against it: where the roof sits on walls, the roof stops on each wall's inner face and the gutter takes its room from that wall's own thickness (Wall Thickness only applies where no wall is found under the eave), and Gutter Width is held to what is left of the wall once a 100 mm outer leaf is taken off. The roof itself is never cut, at any pitch. The outer leaf stands up past the gutter, whatever the pitch, and a coping caps it, so the gutter is hidden from outside.
  5. Click each corner of the footprint, or Pick wall and then a wall or curtain wall; the outline lands on the centre line of what you pick, and Offset takes it out to a face. Close the loop.
  6. Click Finish, choose the Level and Offset in the prompt, and click Confirm.

Select the roof and open Elements in its panel to trim it. Add Fascia, Add Soffit and Add Gutter place a board along every eave, at eave height, in one step; Add Barge Board does the same along every gable edge, and is greyed out with its reason on a roof that has none. An edge that already has the board is left alone, so a second click adds nothing. Each board is then listed under its button: click a row to edit it, or use its bin to delete it. The same tools on the Build toolbar place a board by hand, one edge where you click.

A placed roof's Constraints section holds Base level and Base offset. Base offset is how far the roof is raised above its Base level, and picking another storey under Base level measures it from that storey instead. With Roof armed, Base level is in Parameters before you draw, so the footprint is sketched at that storey's height and the roof lands there.

Draw the footprint with Line, Rectangle or Arc from the top of a mass, or from a point you've snapped to on one, and the eaves start at that height unless you've set an eaves height.

Hip and Flat also follow simple polygon footprints with angled or inward corners, and an L-shape or other outline that one polygon can hold becomes a single roof segment rather than several rectangular wings. Gable and Lean-to on a footprint whose corners are all exactly square are split into rectangles. Any other loop (one wall a degree off, a trapezoid, a parallelogram, a triangle, a five-sided plan, a bay under a metre across) they follow as one roof instead, each eave on its own wall: a Gable stands its vertical ends on the short walls and slopes from the others, so the ridge runs where the two slopes meet, level when the eaves are parallel and rising towards the wider end when they spread, and a Lean-to slopes from one wall and stands vertical on the rest. Gambrel and Mansard do the same on any closed loop: every sloping wall rises at the steep lower angle to a level knuckle line the same distance in from each wall, and the shallower upper angle carries on from there to the ridge. A Gambrel stands its two short end walls vertical in both stages, with the slopes carrying on past a canted end along the line where they meet; a Mansard slopes from every wall. Change a Gable end or the sloping edge afterwards with Edge pitch. The preview and finished roof use the same outline; a hip forms ridges and valleys across it. A polygon hip follows the roof's Angle on every edge until you give an edge a slope of its own, and shallow folds keep their edge lines visible. No wall is refused for its angle: a roof needs only 200 mm of span each way. Drag a corner of a roof made of several wings out of square and the wings become one outline, each wing keeping its own pitch and overhang on its own edges; one line on screen names anything else the wings differed in (the roof type, the eave height, the materials), which then follows the first wing.

The sketch toolbar for a roof has the same tiles as for a floor: Select, Line, Rectangle, Arc, Pick, Pick wall, Join corners, Offset, Trim, Join at corner, Cancel and Finish.

A Rectangle footprint shows live length and width on two sides in plan and 3D. The cursor's Width field and the status bar's Width and Depth track the same size. Type both sizes, or use Tab between the fields, to preview an exact rectangle; Enter adds it to the outline. Escape clears the pending rectangle. Switching between plan and 3D keeps its first corner.

To change a roof's pitch

  1. To change a roof's pitch, select the roof. Use Angle in the roof's Dimensions section to change every mass together; individual slope overrides are kept. While you are still drawing, the same setting is Angle in Parameters (0 to 85°).
  2. Drag Angle, or click its number and type an angle. A higher pitch makes the roof steeper. Each mass shows the same rows (Width, Depth, Eave, Angle, Overhang) in its own Dimensions section under Segments.
  3. For a single slope, open Segments, open its mass, and edit Pitch beside the compass-named slope. A roof-wide Angle applies to every slope, this one included, and Undo brings it back; material changes preserve it; Reset overrides explicitly clears it.

While placing a rooflight or another roof feature on a face, nearby features on that face offer alignment and equal-spacing guides. Thin dashed teal lines mark the edges and centres that line up, and the cursor reads Extension at the placement. A caught corner or endpoint takes precedence. Hold Shift to bypass the alignment, or move clear to release it. The same guides follow the placement in a section or elevation. See Snapping and inference.

To change the slope of each edge

Once the roof loop is closed, an Edge pitches row has a Set all to button that applies one pitch to every edge.

On a polygon hip, the roof's panel lists an Edge pitch row for each edge. Drag one and only that edge changes slope. Choose Gable edge in a row to make that end vertical; the neighbouring slopes meet above it and a wall attached below follows the rake. Slope edge returns that edge to the roof Angle. The slope is defined at the wall line, as in Revit: every face meets the walls at the same height, and the overhang stays the same width all round, so a steeper edge's eave sits lower. The hips and ridges move to meet it in the 3D view, the plan, sections, elevations and DXF alike, and each face keeps its own deck and covering thickness measured square to the slope. Hovering or focusing a row marks that edge on the plan and in 3D. Changing the roof's Angle keeps individual edge overrides; Reset overrides clears them in one undo step. Dragging a corner or splitting an edge also keeps the slopes. All edges follow the Angle does the same without changing the Angle. Every roof type offers Add courtyard, a plain rectangle roof included: the first courtyard gives the roof its outline and keeps its type, so a Gable stays a Gable with its two ends vertical, a Shed still slopes from its low side, and Gambrel and Mansard keep their two bands, with the courtyard sloping inward, in one undo step. Switching the type afterwards keeps the courtyard. Under Courtyards, choose Add courtyard to open a rectangular hole, then set its Width, Depth, Across and Along position, or remove it. A courtyard is refused, with the reason on screen and the roof left as it was, when it lies outside the roof, touches or crosses the outline, overlaps another courtyard, or is too small to stay open once the overhang grows into it. Barge boards and soffits go on a gable edge as on any gable end, following the rake up to the apex. The deck, covering and lining leave it open; its inner eaves face the courtyard, and attached walls below follow the underside there. Plan and section keep the opening. Edit perimeter is unavailable while a roof has a courtyard; edit the courtyard in this panel.

To edit a roof afterwards

Each compass-named slope has its own Pitch. Changing one slope keeps the others at their pitches and moves the shared ridge to meet them. On a gambrel or mansard, the two rows on a compass side are its lower and upper bands: each has its own pitch, and editing either keeps the same roof shape. The first individual pitch edit converts a rectangular mass to an outline roof. Roof-wide Angle, materials and 2D finishes leave individual slope overrides in place. Reset overrides clears the granular pitches and finishes while keeping vertical gable ends vertical; Undo restores them.

Edit perimeter on an existing roof draws the pink outline at the roof's eaves height, on the roof itself, so a corner you drag or snap lands where the roof really is.

Open a slope's own expander for its finish settings. Each slope has its own Material well, which opens the Library, and its own face finishes. Show in 3D controls its material; Show in 2D and Match 3D control its drawn finish. Set a background, pattern or pattern colour on one slope to change that face alone. Its background and surface pattern follow that face in plan, elevation and section; Library materials supply their mapped patterns when 2D matches 3D. Reset its material to inherit the mass's or roof's material again. These choices belong to the placed roof and are saved with it.

Select it. Edit perimeter in the Perimeter section redraws the outline (in a plan, double-clicking the roof opens it too), and the Segments section's Add separate roof mass adds a cross-wing or lean-to. Editing the perimeter of a roof that already has several segments keeps its wings and their separate settings. The roof type, shape, courtyards, structural items, structure, cladding, trim and finishes are all on the roof's own panel, one click from the roof, and an edit there applies to every mass in one Undo step (a value that differs between masses reads Varies). Segments, at the foot of the panel, is for the exceptions: each mass is a row that opens in place with its own width, depth, eave, angle, overhang, edge pitch, slopes, finishes and position. A mass that carries its own settings shows a small dot in the list, and the panel says so above Dimensions while Segments is closed. A roof-wide edit applies to every mass, over its own value, and one Undo brings it back. Both the Segments list and each mass start closed. A segment is never picked on its own: clicking a roof always selects the whole roof. Opening a mass lists its physical slopes, one line per slope with its pitch: two for a gable, four for a hip and one for a lean-to. A small marker identifies a slope that differs from the roof-wide value. The rows are named by compass side and follow the roof when it turns; they are faces of the same roof, so the ridge remains one joined line. Remove mass removes that separate mass and its attached elements; one Undo restores them together. Removing the last mass removes the whole roof straight away. One Undo restores the roof and anything removed with it. Delete on the keyboard and in the right-click menu works the same way. A selection containing items not shown in the view still asks first, naming what goes. While you edit a segment's perimeter, each corner carries a small square that you drag to move it, the same size on screen however far you zoom.

When you finish a hip roof or an edited perimeter and a valley would stop just short of the ridge, Linea says so with the distance and offers to move the corner so the valley meets the ridge, to keep the outline and Set this slope to N degrees on the one edge that lets the valley meet the ridge, or to leave the roof as drawn. Each choice previews live and is one undo step. A corner you leave as drawn isn't asked about again.

To trim a roof segment

Select the roof, expand the segment's row in its panel and switch on Show trim planes. The expanded row makes that segment active for the canvas grips while the roof stays selected. Collapse the row, deselect the roof or change the view mode to clear it. A locked segment has no live grips. Each side then carries a thin line along the top of its plane with a slim chevron on it pointing into the roof: drag the chevron to trim that side back. At a corner, a small square starts a diagonal trim; drag it to cut the corner, and double-click it to remove the diagonal. A diagonal trim has a small square at each end of its line, to set how far it runs along each side. The grips keep the same size on screen however far you zoom.

To set the pitch from the ridge height

In a section, elevation or callout, select a gable, hip or lean-to roof with the Select tool and expand the segment's row in its panel. A dimension locating its ridge appears; type a height and the segment's pitch changes to give that ridge. If the height can't be reached, for instance because of a join or a trim, a message says why and the roof stays as it was. Align, Move and Copy in those views now act on roofs, stairs, columns and railings too.

A locked roof segment stays selectable but draws no trim chevrons or corner grips; unlock it to trim it.

Select a roof segment and the grip at the middle of its outline moves the whole segment, keeping its width, depth and height; undo puts it back in one step. A locked roof or segment, whether locked on its own, through its layer or by a locked group, shows no grips.

In a selected roof's panel, Add Fascia, Add Soffit, Add Barge Board and Add Gutter place the board for you, on the roof, with no clicking: fascias and gutters go along every eave (a gutter only where water drains, and it makes the fascia it hangs on), a barge board along both slopes of every gable end, and a soffit under the eaves and gable ends. The roof stays selected and its panel stays open, so you can press the button again straight away; the new boards appear in its Elements list, and one Ctrl+Z removes everything that click placed. Pressing the button again when every edge already has its board changes nothing and tells you so. If some positions are skipped, the message gives the added and skipped counts and explains which positions were already covered or could not take the trim. If the roof has nowhere for that board (a barge board on a hip roof), the button is unavailable with a not-allowed cursor and hovering it says why; the button never starts the placement tool. Each board then appears in the Elements list under its button, with a select button to edit it and a bin button to delete it (one Ctrl+Z brings it back). The same tools on the toolbar stay manual: you click each edge yourself.

Add Chimney, Add Dormer, Add Rooflight, Add Solar Panel, Add Vent, Add Cupola and Add Eyebrow Vent in the same panel also place the element for you. It lands centred on a sloping face, halfway between the eave and the ridge and turned to face down the slope, and the roof stays selected with its panel open; one Ctrl+Z removes it. Each Add of a kind goes to the roof face holding the fewest of that kind, starting at the left pitch and going round clockwise, so four Adds on a hipped roof land one per face and the fifth returns to the first, while a gable alternates between its two faces. Each one goes clear of what is already there, and if no clear space is left the Add is refused and says so. A solar panel array that is too big for the face is placed as the grid with the most panels that fits (fewer panels than you asked for), and a message tells you the size it took; your remembered array is left as it was, and the Add is refused only if even a single panel will not fit. A dormer, rooflight, eyebrow vent or ridge vent needs a sloping roof, so on a flat roof its button is unavailable with a not-allowed cursor and hovering it says why. Add Segment is unchanged. The toolbar tools stay manual: in plan, section, elevation, callout or 3D, pick the roof face where each one goes. Boards and gutters pick a roof edge, and a downpipe picks its gutter.

A rooflight cuts through the deck and covering in the same orientation as its frame, including on hip faces and roofs drawn with a polygon footprint. A dormer cuts through both layers beneath its interior. In 3D, a plain roof slope keeps its opening rims and outer edges without diagonal triangulation lines around the rooflights. Joined plain roofs draw their exposed ridges and valleys without lines from the layers hidden inside the join. To place a roof feature on a roof inside a group or component, enter it first. A closed group or component stays whole, so its roof and gutters cannot take a new feature until you enter it.

Place a rooflight near an edge and its footprint stays on the roof face beneath it. If the placement falls beyond the eave, the part is brought back onto a face. This works on upper storeys and in a turned building too. If a face is too small for the part, it is centred on that face; reduce the part's size to fit it. That holds when roof parts are all you have selected, and Scale keeps a rooflight on its face too: double it near the eave and it stays on the roof, nudged back as it grows. Select a rooflight together with a wall, a mass or any other part and the whole selection moves, turns, flips and scales as one body: the rooflight is not held to its face and takes the same step as everything else, and it moves onto the roof face under it where there is one. Inside a house type placed more than once, a rooflight or any other roof part goes onto the copy you have entered.

A chimney is a full stack. It stands on the lowest storey of the building its roof sits on and rises through every floor, past the ceilings and out through the roof, and the roof, each floor and each ceiling it passes through are opened around it. Walls are left whole; where a stack overlaps one in plan, it is drawn over the wall. In the chimney's panel, Base picks the storey it starts on and Base Offset raises or lowers its foot from that floor. On a roof that stands on no storey, the stack starts at the roof. Under Steps, Add step widens the stack below a height you choose: pick the Level and an Offset above it, how far it Widens each side, and whether the change is Square, Tapered over its Rise, or Corbelled in courses. Steps add up, so a breast on the ground floor can step in at the first floor and again under the roof. The widening is the same left and right, and in depth the stack grows towards its front; turn on Both sides to grow it at the back too. Flip front turns the front round, and the steps and fireplaces go with it.

Under Fireplaces, Add fireplace puts one on the lowest storey of the stack that has none, and each storey holds one. A fireplace sits on the front face: a firebox recessed into the stack, a hearth in front of it, and a surround with a mantel shelf. Set its Level and Offset, the Opening Width and Opening Height, how far back the firebox goes (Depth) and the Hearth Depth, and switch the Surround or the Mantel shelf off if you don't want them. The opening is never wider than the face it sits in. Each fireplace has its own flue, from above its firebox up to a pot on the stack, so fireplaces on two storeys give two pots. Set the flue Count by hand and it keeps your number; turn Follow fireplaces back on and the fireplaces decide again. In plan the stack is cut and hatched on every storey it passes through, with its flues left open. On a storey with a fireplace the firebox shows as a notch in the front where the plan cuts through it, and the hearth and mantel shelf below the cut are drawn as seen from above. Sections and elevations show the whole stack, its steps and the hollow of each firebox.

Select a fascia, barge or soffit board and its outline carries chevrons and grips. The inner chevron at each edge moves the board up or down; the outer grip, with its end bar, resizes it. As you drag, an edge lines up with the roof's surfaces and with the edges of neighbouring boards. A gutter follows its fascia, so raise the fascia and the gutter hanging on it rises with it.

A rooflight takes the same Panes settings as a window: set its columns and rows, and the dividers between them. On a flat, walk-on or opening rooflight each pane also gets an opener, and Top hung means hinged on the ridge side. A solar panel is moved by its chevrons and sized in Parameters.

A new dormer serves one pane, the same picture window the Window tool starts with; a dormer already in your drawing keeps the grid it has, and the columns and rows stay in its panel. Select a dropped dormer or chimney and its four chevrons move it across the roof, in plan, section, elevation, callout and 3D: it stays seated on the slope as it goes, and a dormer carried across the ridge or onto another roof turns to face down the slope it lands on, as a new one would; a typed distance goes the way the chevron points, and one undo puts it back. A dormer stops with its footprint on the face. Select one on the roof plan that shows its roof, or on the floor plan whose cut passes through its roof, and it shows its distances to the edges of the roof face and to the roof items beside it in blue, like a door's; type a value into one and the dormer moves that way, in one undo step. A value that would take a corner off the roof face or into a neighbouring roof item is refused with the reason. On any other floor the roof is context and nothing is drawn. Its size is in the panel, and so is a chimney's width and depth; a chimney's height above the ridge keeps its own grip. Click the small cube on a dormer's window to bring up the chevrons that size that window.

While the Dormer tool is armed, its window keeps its margins as you change the dormer: a wider dormer widens the window, and raising Eave Height lifts the window's head. Type a window width or height yourself and that one stops following until you next arm the tool. Eave Height is how far the eave stands over the roof at the dormer's centre, so 0 is a real answer: the wall you see hangs below that line. A placed dormer's window stays as you set it, unless you narrow the dormer past it; then the window is cut to fit and a message says so.

A dormer has its own Wall Thickness, Roof Thickness and Roof Overhang in its panel, beside Eave Height and Ridge Rise (the roof's rise from eave to ridge). A thicker wall grows into the room, so the outside of the dormer stays where it is. The window sits back from the face of the wall on a sill, and its foot is held clear of the roof below.

A flush roof with a hidden gutter does not need lining up by hand before its walls attach. Select the walls and the roof and choose Attach Top to Roof: each roof edge near a wall moves onto that wall's outer face as the wall attaches, in one undo step. At the gable ends the wall carries up as a parapet at the height of the eaves.

A dormer has to stand wholly on the roof face beneath it, in plan, section, elevation, callout and 3D alike. Its preview stops where its wall meets the roof, as the built dormer does. Bring its edge close to an edge of the face, a hip's sloped one included, and it catches, its own edge lying on that edge, and the cue at the cursor says Edge. Put the pointer on the middle of an eave and the cue says Midpoint: the dormer's front edge lies on the eave and the dormer centres on that point. A point it cannot sit on, such as the middle of a hip's sloped edge, turns the preview red with the reason and offers no cue. Further over and the preview turns red, and the status line says why for as long as it stays red: a click there places nothing. Hold Shift to place without the catch. Moving or duplicating a dormer follows the same rule, and a refused click leaves it in hand.

A dormer's settings, armed or placed, sit in one row per group: Dimensions, Position, Dormer Roof, Hung Wall, Window, Window Frame and Sill. Open the group you want; the opening and the pane grid share the Window group. Every group opens folded.

To clad a roof

  1. Open a segment's row in the roof's panel and open Cladding. It sits above Trim and starts folded.
  2. Switch on Show cladding. A roof that has never been clad starts as a Seam.
  3. Choose the form, a pattern and the spacing.

The controls are the wall's, with one difference in the pattern names. A roof has a single clad face on each slope, its top, so there is no face to choose. Slope sets lines running down each slope from ridge to eave, which is a standing seam on a gable's two slopes or a hip's four. Eave sets them along the slope, parallel to the eave. Grid and Stagger work as they do on a wall, and so does the = button for an even count. Joint boards the covering with gaps between the boards; Seam stands ribs on it. A Joint cladding goes on roofs whose faces are not too steep for it, and a Seam goes on any.

Each line is clipped to its face, so on a hip the seams shorten towards the apex of the end. The cladding is part of the roof slab: it follows the trims you set, and a rooflight or dormer cut through the roof takes the cladding with it. It needs a roof with some thickness, so give the segment a deck or covering first; if it has none, a note says so.

The same notes apply as on a wall. A spacing wider than the roof face is refused, so choose a smaller one; a very fine pattern applies with a note that it will slow the model down; and a roof carries fewer pieces than a wall, so a pattern too fine for a roof is refused. Choose a wider spacing.