Rooms and areas
Rooms and areas. A room is a named, numbered space that appears in the room schedule. An area is a drawn figure you total as GIA, GEA or other.
Inside an entered group or component, boundary grips follow the turned room or area. Arrow locks use that container's local axes.
While tracing a room or area by hand, the corners already placed can offer guides for the next leg. A matching-end guide reads Extension; see Snapping and inference.
With Re-place room armed, hovering a room highlights it while you choose it.
To draw a room by hand
- Click Room on the left rail (in 2D or 3D; Split's rail keeps Select only).
- Click each corner of the boundary, or type its length at the Length prompt. Corners snap to walls and other geometry, and guides show where a corner lines up.
- Close it by clicking the first point again (you need at least three points). The room lands as the outline closes.
A room drawn by hand is a real room: it takes the next room number on its level, a name you can change, an area, a label and a row in the room schedule. Room detection never adopts it, reshapes it or adds a second room over it, so it stays where you put it. It is the fallback when automatic rooms go wrong, and the way to rescue a room whose walls are gone.
Rename a room in Parameters and, if another room already has that name, a line under the field says so. Enter still keeps the name, as two rooms may share one, and no other room is renamed. A room number is different: a number another room holds is refused, and the line names the room that has it. Label shows switches each line of the room's label on or off for that room: Name, Number, Area, Ceiling height, Finishes and Occupancy. A room keeps at least one line on, so the plan can still pick it, and the sheet, the PDF and the DWG follow the plan. Name style sets the room name bold or regular; a name made bold is written on a bold text style in a DWG.
Select a hand-drawn room afterwards and its boundary carries small squares at each corner and a smaller one at the middle of each edge, which you drag to move a corner or to add one. Room and Area draw in the same sketch a floor does, so a corner snaps the way a floor's corner does. The room or area is made the moment the outline closes (a Rectangle's second corner, a polyline closed on its first point), with no tick to press, and the tool stays armed for the next. To add several outlines to one room or area, switch on Several outlines on the sketch bar (it stays on until you switch it off): each closed outline then stays open, and you click the tick to finish. Escape drops the live leg and keeps every corner you have placed; pressing it again does nothing, and it only leaves the tool when nothing is placed yet. The green tick (or Enter) makes the room from what you have drawn, and the cross throws the outline away. With fewer than three corners there is no room to place. For an exact edge, type its length at the Length prompt. Drawing in 3D, a corner clicked near an existing point is caught and marked with a circle.
A locked room or area stays selectable but draws no corner or edge grips.
Edit boundary in a hand-drawn room's or area's panel opens the same sketch a floor's Edit perimeter opens, on the room's outline. Select an edge or a corner, drag a box round several, Ctrl-click to add more, then Move, Rotate, Scale, Flip or Mirror them; use Line, Curve or Rectangle to add to the outline. The room is not changed until you click the tick, the cross leaves it as it was, and a boundary that crosses itself keeps the tick grey with the reason beside the bar. Clicking the tick releases the room from any walls it followed, keeps its name, number and finishes, and its area, label and schedule row read the new outline. A curve in the outline is saved as the straight edges it is made of. A room that still follows its walls shows Edit boundary greyed; use Make editable first. In the plan, clicking a room's label selects the room and tints its whole area, and double-clicking the label opens Edit boundary directly; on a room that follows its walls the double-click tells you so and leaves the room as it is.
With Room or Area armed, Parameters shows the colour, whether it is filled and its Ceiling height (it reads Automatic until you set one) before you draw, and the next room or area takes them; a height you set there is kept as set. Its name, number and whether it is a room or an area come from the tile you armed. A room's Ceiling height follows what bounds it: the ceiling over it on its storey (the lowest, where several cover it), else the underside of the slab above, else the storey's own height, so placing, moving or deleting a ceiling updates the label straight away. Type a value in the room's panel and it is kept as set; Automatic returns it to the derived height.
To draw an area
A room's colour picker sets its own opacity. Styles > Fills > Room fill opacity adjusts all room fills in this drawing, starting at 20%. Selecting a room keeps its fill strength, and sheets and PDFs follow the same setting.
- Click Area on the left rail, below Room.
- Click each corner, and close it as you would a room.
- Select the area and pick GIA, GEA or Other under Type in its panel.
An area is outline plus a label showing its name, type and area. It has no room number and is not a room: it does not appear in the room schedule or count as a room, and room detection leaves it alone. Its corners are free to drag. The Level totals in its panel, and the rows at the foot of the area schedule on the plan, add the drawn areas up per level for each type.
Detected rooms follow the walls, curtain walls and room separators that enclose them. They have no corner or edge grips, and dragging, Move and arrow keys leave their boundary in place. Pasting or duplicating a detected room on its own is refused. Copy it together with its complete enclosing walls, curtain walls or room separators to carry the room with them. You can still select it, move its label, edit its name, number and parameters, or delete it. To change its shape, edit the enclosing boundaries; to move it into another enclosure, use Move to another area below. Deleting a wall that encloses a room keeps the room, with its name, number and parameters. While its boundary is open the tag reads "Not enclosed" in place of the area, no fill is drawn, and the room schedule and Parameters say the same. Draw the wall again, or Undo, and the area comes back. Setting Enclosure to Open by hand does the same for any room and holds until you change the switch, whatever happens to the walls around it; Auto-detect hands a detected room back to the walls. A room you draw yourself is enclosed by its own outline and keeps its area unless you set it to Open.
Drag a room's label, or the name of a named zone, to move the label. Its panel then shows Label position as Placed, and Reset puts the label back where the plan places it. Choosing Reset label position from the room's right-click menu does the same in one undo step. Double-clicking a room's label opens its Edit boundary instead. A thin leader joins the label to its room when it sits outside the room's outline. In a section or an elevation the room's tag drags the same way, and each view remembers its own position, so moving it in one view leaves the plan and the other views as they were.
A room's name shows in the plan, in sections and elevations, and on sheets. The 3D view draws the room's tinted floor and edge, with no name or pin over it, so rename a room from its panel or in the plan.
Grouping all the walls around a room carries the room with them, including a hand-drawn room with the same boundary. Its name, number, area and finishes stay with it, and an upper-storey room stays on its own plan. Ungroup keeps the rooms with their enclosing walls. A room enclosed by the walls of a component belongs to that component. Every placed copy carries its own room, which appears in the room schedule and takes the next number on the level where that copy stands, so the same component placed on two storeys gives each storey its own numbering.
To make a detected room editable, or bind a hand-drawn one to its walls
Select a detected room and click Make editable in its Room position panel, or right-click it and choose Make editable. It keeps its name and number and becomes a hand-drawn room whose corners you can drag; detection leaves it alone from then on. If a deleted wall had left it reading Not enclosed, Make editable brings its area back, unless you set it to Open yourself. To go back, select the room and click Follow walls (the same panel, or the right-click menu). It takes the boundary of the walls and room separators around it exactly, and follows them again. If nothing encloses the room, or another room already follows that enclosure, nothing changes and you are told why. One Undo puts either one back.
To divide a room, or close an opening between two rooms
Where an opening joins two rooms they read as one room until something closes it, and a room you want in two parts needs a line drawn across it. A room separator is that line: it bounds a room exactly as a wall does, so the two rooms come out as two, with areas that add up to the whole.
- Open the level plan whose room you are dividing, in 2D.
- Click Room separator, the last tile in the drafting group on the left rail, after Region.
- Click one end of the line, then the other end, straight across the opening or the room.
- The room is now two rooms. Select the line to move it or delete it, and the rooms follow.
A line that ends on a wall's end face, or close to the end of a wall, joins that wall. A separator can run between two walls, from a wall into the open, or across open floor, where four of them make a room with no walls at all.
Draw a separator on the level plan whose rooms it bounds. It is drawn on its own Room separators layer and always looks the same, a pale green dashed line, whatever that layer's colour or line style, so it has no colour, weight or pattern fields of its own. It does not plot: it never appears on a sheet, in a PDF, a DWG or DXF file, or in print, in any view. Select it, move it or delete it like any other line, and the rooms follow.
A separator drawn right across a hand-drawn room bounds it too: the room keeps the side its centre is on, and its area is that side only. Move the separator and the room follows; delete it and the room is whole again. A separator can bend: two or more lines that meet end to end, or one polyline, bound the room the same way once the path runs from its outline across to its outline. A separator that stops inside the room, short of its outline, bounds nothing.
To move a room to another area
- Select the room and click Move to another area in its Room position panel.
- Click inside the enclosed area you want it to take.
The room keeps its name and number and takes that area's boundary. If the area you click already has a room, the two swap places. If it has none, the room moves there and the area it left stays without one. One Undo puts it back. Escape lets go of the room, and Escape again leaves the tool.