Massing rectangles and circles

The Massing toolbar blocks out a scheme. A footprint you draw is a flat face until you push it up with Extrude.

After placing a Rectangle's first corner or a Circle's centre, you can switch between plan and 3D and continue the same shape. Its preview follows the pointer from the point you placed.

While tracing a Polygon, earlier straight legs can guide a parallel leg and a corner level with an earlier end, in plan and in 3D. These guides follow the polygon's drawing plane. See Snapping and inference.

A flat face is white on its top side and blue-grey on its underside. Orbit below it and the face is still there, drawn in that blue-grey, whether it is a single rectangle, a circle or one piece of a crossing. A standing face is white on the side it was drawn on and blue-grey on the other. Paint stays on the side it was put on, and a side with no paint keeps its own colour.

In 3D, Bulge catches nearby model points while you shape the arc. Its preview and placed arc use the caught point within the edge's curvature limit.

The Massing toolbar keeps the same tiles, order and shortcuts in plan, section, elevation and callout views, including a callout of a plan or a section. T arms Reference plane in every 2D drawing. Pencil closes model lines into a face; Rectangle and Circle make model faces on the drawing plane. In a section, an elevation or a callout on a section, that is the plane the view has set, and Set plane on the toolbar picks it: see Setting a plane to draw on. The result is part of the model and appears in other views and in 3D. The Draft tools remain available for view-only linework.

The Massing toolbar along the bottom of the 3D view, with a rectangle drawn flat on the ground beside a house.
The Massing toolbar, and a rectangle drawn on the ground.

Click the tab at the left edge of the bottom toolbar to switch to Massing. Its tools, in order, are Pencil, Rectangle, Circle, Pie, Bulge edge, Polygon, Arc, Extrude, Axes, Offset, Eraser, Follow Me, Model text, Dimension and Reference plane. Clipper and Painting are on the left toolbar. Axes works in the plan as well as in 3D: click the origin, then click along the direction you want red to run. On a narrow window, the last tiles on the Massing toolbar sit in the More tools menu at the end of the bar, and their keyboard shortcuts work the same.

To draw a rectangle

  1. Click Rectangle.
  2. Click one corner, then the opposite corner. Or type a Width, then Depth, and press Enter.

After you set the drawing axes with Axes, a rectangle runs along them: its first side follows red and its second follows green, whether you click the corners or type a Width and Depth. Turning the view does not change this.

Rectangle shows the live width and depth while you point, in 3D and in plan. A snap word names the point the corner will land on, in 3D and in plan. Passing over a point can offer a From Point guide along a rectangle axis, in 3D and in plan, and the corner lands on it. A rectangle started on a vertical face stays on that face. An arrow key chooses the drawing plane; press the same key again to release it, or another arrow to replace it. A held plane takes priority over a nearby catch.

With a massing tool armed, Parameters shows Base offset under Dimensions: set it and the shape lands that far above the ground or flat face you draw on. On a placed mass, Base offset is where its underside stands above its level, and moving it lifts the whole mass. Base level lists the storeys of the building: pick one with the tool armed and the mass is built on that storey, its underside Base offset above that storey's floor. On a placed mass, picking another storey moves the mass onto it and leaves it at the same height in the model, with Base offset adjusted to match; it then rises and falls with that storey, and one undo puts it back. Select several masses and one pick moves them all. A mass inside a group shows Base level unavailable with a not-allowed cursor. A shape drawn on a sloping or upright face stays on that face.

A face and the edges that formed it travel together when you change its level or offset, move, turn, scale, copy or group it. This also applies after Extrude turns it into a solid. Click an edge to select that edge; double-click a face to select it with its edges. Moving one edge reshapes the face.

To draw a circle

  1. Click Circle.
  2. Click the centre, then set the radius with a second click, or type a Radius and press Enter.

In plan, an arrow key holds the radius on an axis (right for red, left for green), and drawing close to an axis leans it onto that axis. Hold Alt to set the radius free.

With Circle, Pie or Arc armed, Parameters shows Sides, the number of straight segments in one full turn, from 3 to 256. Set it to 12 and the shape is drawn as a twelve-sided figure. The number is remembered for the next one you draw. Inside a turned group, the Circle preview shows the same outline that the final click places.

To draw a pie

  1. Click Pie in Massing, in plan or 3D.
  2. Click the centre, then point in the start direction. Click to set the radius, or type Radius, Tab for Start direction, and press Enter.
  3. Move round the centre to set the sweep, then click, or type the Sweep angle and press Enter. Sweeps over 180 degrees work too.
  4. The arc closes through the centre into a flat face. Its curved side is one curve, whatever its Sides: a click picks it whole, and the Eraser takes it whole. Use Extrude to give it height.

To bulge an existing footprint edge

Click Bulge edge, pick a straight footprint edge, then move to bow it and click to commit. You can also drag the edge and release. Type a Sagitta (the distance from the old edge to the middle of the arc), or press Tab for Radius, then Enter. The other edges, height and paint on surviving faces stay in place. In a section or an elevation, the edge you pick is the footprint edge drawn crossing the cut plane under your pointer, as a vertical line from the mass's base to its top, and where masses are stacked the height you click chooses between them. The arc passes through the point you move to along the cut plane, and it bows the footprint, since a mass is bulged in plan. Escape cancels; one undo restores the straight edge.

On an existing massed face, draw a smaller face inside it and use Extrude to push or pull it. Parametric walls and roofs keep their own editing tools.

A circle drawn on a face of a block keeps its rim as one smooth curve. Push it in with Extrude and the recess is one smooth surface, not a ring of flat strips.

Press Delete or Backspace to remove the selection while a Massing tool is armed. If a footprint is in progress, the first press cancels its current leg like Esc and the next press deletes the selection. The tool stays armed. Backspace in a number field edits the number.