Repeating details
A repeating detail lays a detail component along a path: a course of bricks, roof tiles up a rafter, cladding boards, shingles, joists at centres. You draw the path once and the units lay themselves out along it, in a plan, a section, an elevation or a callout window.
Select a repeating detail and edit Dimensions > Length to move its end along the view-local run while its start stays put.
Snap either end of the path to a wall or one of its Parts to bind the whole repeat to it. The first bound end owns the path when both ends snap. The repeat follows that feature through Move, nudge, Parameters and wall end drags, in the view you placed it in; a Part binding follows its pulled edge too. The wall or Part and repeat undo together. A path placed in empty space stays put. Removing its target leaves the repeat at its last position. A callout draws its parent's repeating details inside its crop on screen, on sheets and in PDF, DWG and DXF. A repeat placed in the callout stays in that callout and does not show back in its parent.
An insulation batt unit carries the same round quilt as a placed detail component or an insulation layer. Changing its Thickness scales both the width and height of the bulbs; Length sets where that unit's stroke ends.
To lay one
- Open the view you are detailing: the plan, or a section, an elevation or a callout window from the Views chip.
- Click the Library pill, go to Detailing and expand Detail components on the rail. Switch the pair above the tiles from Place to Repeat along a path.
- Pick the unit by its tile. The line under the heading says where the repeat will land, for example the plan or the name of the section.
- Set the Alignment in the card that opens when the tool is armed: Outer face, Centre or Inner face, the same three as a wall. It says which face of the run sits on the line you click, so a brick course clicked along a wall's outer face can lie against it exactly. Space puts the run on the other side of the line. Click the start of the path, then its end. The units lay out as the pointer moves, so you see them before you commit, and the length shows as you draw. The second click lays that leg and starts the next one from the same point, with the same unit, alignment and side, like a wall chain; each leg is its own repeat and one Undo removes one leg. Corners are not mitred, so a unit stops at the end of its leg. Enter with no typed length or Escape ends the run and keeps every leg already placed; a second Escape leaves the tool.
The path takes the view's snaps, and Alt turns the magnet off. The arrow-key locks hold the direction before the first click, after it and part-way along, with their guide drawn. Once the start is down you can type a Length, press Tab for an Angle and press Enter to lay the repeat at that distance.
The units
Any detail component type is a unit. Pick a family in the list, then choose Plan, Section or Elevation below Place and Repeat along a path. Plan offers horizontal cuts, running lengths and top faces. Roof tiles show their width by gauge: 165 x 100 mm for the plain tile, 330 x 320 or 230 x 305 mm for the interlocking tiles. A Plan repeat lays these faces along their width; use Courses and the Running bond to stagger the next course. Plan shingles offer 100, 150 and 200 mm widths, or a repeating mix. Section offers the cut units, such as brick and block, roof tiles, cladding, shingles, timber, battens and wall ties. Elevation offers their faces, including brick stretchers, headers and soldiers. A family stays selected when you switch the toggle, and stays in the list when it has no units for that view. The units you choose are placed into the drawing in front of you.
The tool starts from the layout the unit usually wants. Masonry fills the path with a 10 mm joint. The joint stays an empty gap, and the two short lines that close it at each face draw at the thinnest pen, while the brick and block outlines keep the pen of the run; a joint of 0 draws no closing lines. A roof tile in section sits at its gauge: a plain tile 265 long with a 65 mm head lap is laid 100 mm apart, and an interlocking tile at its length less the lap. Cladding goes at its board width less the lap, a shingle at its exposure, timber in section at 400 centres and wall ties at 450. Timber and batten elevation faces lie end to end. Tile, cladding and shingle elevation faces repeat at the same gauge, cover and exposure as their cut partners, with their coursing dimension along the path. Tiles, feather-edge boards and shingles overlap, so each starts stood at its lap inclination: hanging by its head, with its tail lifted by the thickness it rests on, so the units sit on one another and do not pass through. You can change any of it afterwards.
A run stands as its Library thumbnail shows the unit. In a section, an elevation or a callout taken from a section, a Brick 102.5 x 65 laid up a vertical path is 102.5 across the path and 65 along it; the preview and the placed run agree. In a plan a course follows its path, as a wall does. Roof tile, cladding and shingle always follow the path, tail to head, in every view. A cut unit is hatched as its material is in a wall build-up, and Hatched on its type gives the bare outline (see Detail components). The size, Spacing and Course height fields read in the model's own unit, so on a millimetre model you can type 140mm or 0.14m and either lands.
The four layouts
Pick the rule from the Layout list in the panel.
- Fill lays units one after another with the spacing as the joint between them, until the path is full. A 2 m path of 215 mm bricks with 10 mm joints gives nine units, 225 mm apart.
- Distance lays them at a fixed distance, centre to centre. 225 mm on the same path gives the same nine.
- Number spaces a count you choose evenly, the first at the start and the last ending at the end: five bricks on the same path are about 446 mm apart.
- Maximum lays the fewest units whose spacing stays at or under the figure you give: 300 mm on the same path gives seven, 297.5 mm apart.
Only whole units decides the end. Off, the unit that crosses the end of the path is kept and cut there, drawn as the piece that is left, so a course finishes flush. On, only whole units are kept. It is for Fill and Distance: Number and Maximum always lay whole units along a plain course, evenly from the start to the end (a course a bond has offset can still hang over the start). Other side of the path swaps which side of the line the units stand on, and Unit rotation turns each unit relative to the path.
Background fill
Tick Background fill in the Fill group of the panel to lay a flat colour behind the whole repeat, joints between the units included. Background colour picks it; Auto takes the repeat's own colour, from its line style or its layer. The fill is drawn behind the units and their hatch, goes to a PDF as it is, and is written to a DWG or DXF as a solid hatch under the units. It is off until you tick it, so an existing drawing is unchanged.
Foreground fill
Foreground fill fills the units themselves, the blocks or bricks, and leaves the joints to the background fill. Give the blocks a dark grey and the mortar a light one and the wall reads as blockwork. Foreground colour picks it, with its own Auto, which is a soft tint of the repeat's line colour so the hatch and outline stay readable over it; the swatch shows the tint it will draw. It sits above the background fill and under each unit's hatch and outline, goes to a PDF as it is, and is written to a DWG or DXF inside each unit's block, so one unit is one block and moving it in CAD moves its fill with it. Both fills are in the panel for one repeat and for a selection of several, and each is off until you tick it.
Courses and bonds
A repeat is one course along its path. To lay a wall of brick or block, raise Courses in the Courses and bond group of the panel: each further course stands one Course height out from the one before, on the same side of the path, and by default that is the unit's own height plus its joint, 75 mm for a 65 mm brick with the 10 mm joint. Type a height of your own and it stays; switch Course height from the unit back on and it follows the unit again. The Bond list says how each course lies on the one below: Running, Stack, English or Flemish.
- Running offsets every other course by half a unit and a joint, so on 215 mm bricks the second course starts 112.5 mm in. It is the stretcher bond, and the one a repeat starts with.
- Stack puts every course straight over the last, so the joints run up in lines.
- English alternates a course of stretchers with a course of headers. A header is the brick seen end-on, 102.5 mm long for a 215 mm brick with a 10 mm joint, and the header course is lapped a quarter brick, so no joint lies over another.
- Flemish alternates a stretcher and a header within every course, and offsets every other course so each header sits centred over the stretcher below.
Where a course is offset, its first unit hangs back over the start of the path, so a half bat is cut at the start as well as at the end, flush with the path in both places. Only whole units drops those half bats. Only brick, in section or elevation, has a header; a block or any other unit lays English and Flemish as a running bond. A Flemish course sets its own spacing, so the spacing figure only matters to it as the joint under Fill. A header is its own unit type in a DXF, such as Brick 102.5x65.
To change one
Select a repeat by clicking its path or the edge of a unit. The Unit group of the panel is the detail component's own: the type picker, its name and its size in millimetres. Size belongs to the type, so changing it changes every repeat and every placed component of that type, in one undo step, and the units lay out again. Layout holds the rule, the spacing, the count, the end and the side, with a line saying how many units the rule gives along the path and whether the last is cut. With several repeats of one unit type selected, the size still edits that one type; repeats of different types show Varies until they share one.
A selected repeat has a grip at each end of its path, in the plan and in a section, an elevation or a callout window. Drag one and the units lay out again as you drag. Under Fill and Distance the end steps in half and full units from the other end. The floating Length field and the status bar Length follow the landed end while you drag. The readout beside the coordinates counts units, including halves such as 12.5 units, and clears when you let go. Under Fill, a unit includes its joint: a 215 mm brick with a 10 mm joint steps by 112.5 mm for a half and 225 mm for a full unit. Under Distance, the steps follow half and full spacing, including a tile gauge, board cover or shingle exposure. A point you snap to on the drawing, such as the end of a line or where two lines cross, wins over the unit and the end lands exactly on it. A Fixed Distance of zero or less leaves the end where it was. The arrow-key locks still hold the direction, Alt turns the snapping off and leaves the length free, you can type an exact length from the other end, and the whole drag is one undo step. In the plan, Move, Rotate, Flip and Duplicate carry a repeat like any element. In a section, an elevation or a callout window, Move, Copy, Rotate and Mirror take it as they take a drawn line. Mirror reflects the course about the line you pick and puts the units on the other side, so it is a true reflection and not just a turn.
Drawing against a repeat uses its geometry: the two ends and the middle of its path, and the corners and edges of its units, are snap points in the view the repeat belongs to. A course drawn inside a flipped group lands on the side its preview showed.
A dimension attaches to the corners and edges of a repeat's units, and to the ends and middle of its path, as it does to a wall: pick one when you place the dimension, or drag a dimension's witness grip onto it, in the view the repeat belongs to. Change the course and the dimension follows.
In a plan, section, elevation or callout, Align can use the path or a straight unit edge as a reference, and a wall edge picked first is a reference for a repeat too; the repeat lights as the pointer comes to its edge. Click the reference first, then a parallel edge of the repeat to move. Both ends move together in the drawing's plane, so the layout stays the same, and one Undo puts it back. Only repeats drawn in the current view take part. A locked repeat or layer stays put.
In DWG and DXF
Export as DWG, or choose DXF as the alternative. Each whole unit leaves as an insert of its detail component's block, named after the type, such as Brick 215x65, on the layer you drew the repeat on, so a CAD user can count and edit them. An insert cannot be clipped, so a unit cut at the end of the path leaves as plain lines and outlines on the same layer. A repeat with a line style writes that style on its inserts.
Plan, section and elevation exports follow the drawing's phase styles for whole units and clipped end pieces. By default, Existing repeats are halftoned and Demolished repeats are dashed with no fill or hatch. Whole units keep their block inserts in CAD, on the repeat's phase layer.
Corb can lay a repeat: name the unit, the path and a layout, and for masonry the number of courses and a bond, and he tells you how many units it laid and whether the last was cut.