Drawing railings

A railing is a run of posts along a line you draw.

Use Parameters > Dimensions > Length for a straight two-point railing or fence: its start stays put and its end moves along the run. A curved run, several legs or a railing paired with a stair shows a read-only centreline length instead. Values below 100 mm are refused.

Select several railings and the panel edits them together: length, curve, Top constraint, Top offset and the balustrade settings apply to each of them in a single undo step, and a setting they differ on reads Varies.

In Parameters, each section is a row that opens folded, as a stair's do, and Materials is one of them: a swatch for the frame and, once the infill is glass, one for the glass. Pick a swatch, then choose its material in the Library. Auto returns it to the default.

A curved railing's handrail follows the curve as one continuous length, with newel posts at the ends. Its spindles and glass follow the same path.

  1. Click Railing on the Build toolbar.
  2. Click to add a post along the run, and keep clicking to carry the run on.
  3. Double-click, or press Enter, to finish the run.

A run drawn along the top of a mass or a wall stands on it, at that height.

To set where it stands

Every railing has a Constraints section in Parameters; with a balustrade armed and nothing else above it, the same section is headed Dimensions. Base offset lifts the railing above the floor it stands on, or above the slab it is drawn on, and Height stays the guard height measured from there. With the tool armed, Base level and Base offset are both in Parameters: pick another storey and the next railing you draw stands at that storey's height plus the offset, and the preview is drawn there. Picking the storey you are drawing on clears it. A Base level left over from another drawing is ignored, and the railing stands on the storey you are drawing on. On a placed railing, Base level measures it from another storey of the same building instead, and it moves when that storey's height or elevation changes.

Top constraint sits below them. It reads Unconnected to begin with, which keeps the guard Height you set. Pick a storey and the top follows it, plus a Top offset, while Height becomes a read-out of what that gives. A top that would leave the guard under 0.3 m is refused with a message. A railing paired with a stair keeps the stair's heights, so the Top rows don't appear for it.

Escape or Enter lands the run so far and drops the live leg. One Undo removes that landed run. As with walls, you can type a length and angle as you place each leg; see Typing exact values. Parameters lists the last Look used and carries it to the next railing.

To change the look

Select a railing and open Railing in Parameters. Look is one dropdown: Classic, Traditional, Glass + timber, Frameless glass and Utility. Changing Look keeps the path you drew: straight legs stay straight, and authored curves stay curved. A customised combination shows its nearest Look without changing its parts. Traditional gives newel posts, a handrail, a base rail and spindles. Utility is the same parts made plain and metallic: 48 mm round tube posts, a round 42 mm tube handrail and 12 mm round bars, continuous round landings and turns. A railing paired with a stair takes the stair's Look, Utility included. Glass swaps the spindles for glass panes between the posts. Frameless drops the posts, the handrail and the base rail, and the glass runs the whole length, down past the floor edge it is fixed to.

The balustrade looks use the same parts and rows as a stair's Railing section: pick a look, then switch any part on or off. Spindle spacing sets the chosen clear gap between spindles; the default is 100 mm.

To change the parts

Height sets the guard height, Newel posts, Newel size, Newel height (how far the top of a post stands above the top of the handrail: 80 mm for a square post, flush for a round or flat one, until you change it) and Post section (Square, Round tube or Flat bar) the posts, Handrail the rail on top, Handrail profile whether that rail is Rectangular (a flat section) or Round (a cylinder), Handrail width and Handrail height the size of a Rectangular rail (each set on its own, 62 by 44 mm until you change them) or Handrail diameter the size of a Round one (44 mm), Bottom rail the rail the infill stands in (switch it off and the spindles run straight to the floor, or to the tread on a stair), Rails and Rail spacing extra level rails between the handrail and the bottom, and Infill is Spindles, Glass or None. Spindles follow the clear gap set by Spindle spacing; Spindle thickness sets the section. Glass is one pane for each bay between posts, split into equal panes when a bay is longer than Pane width (1.2 m until you change it), with Pane gap (10 mm) between them; Glass thickness (12 mm) sets how thick the glass is, and sections show it.

A corner gets a newel post when posts are on, and the handrails meet along a mitre when they are off. Each leg of a run draws its own panes. Spindles meet the handrail underside and the bottom rail flush, including on a rake, and sections show two silhouette sides for a round spindle. Glass has its own entry in Materials, so the panes paint apart from the frame, and sections and elevations draw them. Pick Classic and the railing goes back to its original build.

In plan

The five balustrade looks are drawn in plan the same simple way, at every detail level: the handrail as a band of two parallel lines, as wide as the rail you set, that runs on round each turn and stops at each post, and a small shape for each post at the ends and turns, in the drawing's ink: a square turned to match the leg it ends, or a circle for a round post. Spindles, balusters, glass panes and the base rail are built in 3D and are not drawn in plan. A Frameless railing has no handrail, so the run of its glass stands in for one. A railing that climbs is drawn solid where it is below the cut plane and dashed above it. A railing paired with a stair reads as one run with it, sharing the stair's top post, and the same lines go out to DWG and DXF on the railing's layer.

To pair a railing with a stair

Select a railing on a level a stair leaves or arrives at, and pick the stair under Pair with stair. The railing takes that stair's look: its infill, posts, handrail, heights, glass settings and materials. It keeps them when the stair changes, so change the stair's infill and the railing follows. Where the railing meets the stair's top newel the two share that one post, and the handrail runs on from the stair's into the railing's at the same height. Pick None to unpair; the railing keeps the look it had as its own.

Spans of a paired railing that run along one of the stair's handrails rise and fall with that flight. A span that runs elsewhere, such as a guard across a landing, stays level at its own height. Pairing records which is which, so moving the stair later does not change it. If a flight a span was riding is removed, or you add or remove a point on the railing's path, those spans stand level and a note under Pair with stair says so. Choose None, then the stair again, to tie them afresh.

A Glass railing and a Glass stair draw the same frame and the same glass until you paint one, so they sit side by side as one guard. A paired railing wears the stair's paint; to recolour both, paint the stair.

To change one

Select a railing in 3D and a slim chevron stands just past each end, halfway up, pointing out along the run: click it to move that end along the railing's own line, with the snaps it meets on that line. A small dot at the end moves that end freely. A railing of several legs wears the same chevron and dot at its two ends, and every corner dot, like the ends, lands on a slab edge, a wall face or another railing's end when you bring it close. A chevron above the top sets the height. Each chevron keeps the same size on screen however far you zoom, and on a curved railing the end chevrons follow the curve.