Sections, elevations and callouts

Sections, elevations and callouts are drawings cut from the same model. Draw the marker on the plan and the drawing exists.

Select a line drawn in the view and press an arrow key to nudge it along the drawing's horizontal or vertical direction. Shift moves ten grid steps, and each press undoes in one step. This works on upper storeys too.

Massing shows here as it does in 3D: the lines that divide a face, the rings Offset leaves on one and model lines all draw in the view, hidden by whatever stands in front of them. To draw massing from a section, an elevation or a callout on one, the view asks for a plane first: a face in the view or in 3D, or the view's own plane. See Setting a plane to draw on.

To delete a section, elevation or callout, choose Delete from its row's three-dot menu in Views, including while a sheet is open. Its own drafting, dimensions and sheet placements go with it. One Undo restores them together.

A section marker has Dimensions > Length. Its first cut-line point stays put, its second moves along the line, and the view direction stays the same.

Flip moves a callout's bubble and leader to the opposite side while its box stays put and its text stays upright. Flip again to return it exactly. On a section or elevation marker, Flip changes the head's facing side while keeping the cut line fixed and the head's text upright. A tag flips to the other side of its leader tip while its text stays upright; a tag without a leader flips about its placement point. Mirror reflects the whole annotation across the axis you place. In a section or elevation, with a piece selected, Mirror's Vertical axis previews at the pointer over empty paper and a click there sets the axis; Horizontal is greyed there with its reason.

With Select active, press an object's body and drag to move it in the drawing. An unselected object is selected first. Closed groups and components, including massing, move as one piece. The geometry follows the pointer with Move's live preview and snaps; releasing finishes one undoable move and leaves Select active. See Select and Walk.

A line, a text note or a dimension drawn in a section, an elevation or a callout is picked by its line, as in the plan: a few pixels either side of it takes it, further off does not, and hover lights the same one a click would take. Where it crosses a cut wall, a press on the wall's body takes the wall, a press just outside the wall takes the line, and a line drawn on the wall takes the line.

Arm Door, Opening or Window in a section, an elevation or a callout and click a wall in the drawing. The preview is an outline of the opening's width and height across the wall's thickness, blue on a wall and red where no wall is under the pointer; in a callout over a plan it is the plan symbol. A door or window already in the wall does not hide the wall from the pointer, and the preview goes when the pointer leaves the drawing.

When placing a roof feature in a section or elevation, alignment guides follow its position in that drawing and read Extension where it lands. Door and window head and sill guides can line up across a wall corner. Detail lines drawn in the view stay available as snap targets at their drawn positions while you edit inside a placed copy of a building. See Snapping and inference.

With Extrude, Offset, Follow Me, Eraser or Paint active, Face and Edge identify the surface under the pointer before a click. These cues work in sections, elevations and callouts over either a plan or a section. In Split, they follow the pane under the pointer.

For Pencil on a captured drawing, Enter and Escape both close the clicked points into the same face when enough points have been placed; the live preview is left out. One Undo removes the landed run and face together.

Inside an entered group or component, a wall end grip follows the run where it is drawn in the cut. Arrow locks use the container's local axes that lie in the view, and the guide follows the constrained preview. A typed length measures from the fixed end.

To divide a straight wall's layers at a height, select its parts, or the wall with parts, and choose Divide Parts. Click twice across them in this drawing; the line previews with the drawing's snaps and axis locks, and accepts a typed length. Selecting one leaf divides only that leaf. Esc drops a started line, then disarms Divide; changing views also disarms it. See Parts for changing the lower piece's material.

A callout over a plan keeps its own drawing scale for its pens and symbols, including while you drag an object with Select or Move. A selected groupโ€™s outline follows the group as one piece. Enter a placed component to select its members in the callout; its other placements stay outside that editing context.

A callout shows its own window and what is anchored in it. A tag, a door or window mark, a room name or a stair tag stays while the element it marks reaches the window (a mark in the margin round a door that is inside stays, a mark for a door outside goes), a grid bubble whose line is outside is left off, and a section line shows where it crosses the window. Nothing draws more than a few millimetres of paper beyond the window's edge, in the open view, on a sheet and in the PDF. Press in a callout and you pick what the plan picks at the same point: the wall within a pixel or two of its face, the door on its swing arc, and nothing in the clear paper between.

A callout also draws its parent's detail components and repeating details, clipped to the callout crop. This carries through to its sheet viewport, PDF, DWG and DXF. Details placed in the callout stay in that callout and do not appear back in its parent. A detail snapped to a wall or one of its Parts follows that element in its view; a free placement stays where it was put.

With Select active, press an object's body and drag to move it in the drawing. An unselected object is selected first. Closed groups and components, including massing, move as one piece. The geometry follows the pointer with Move's live preview and snaps; releasing finishes one undoable move and leaves Select active. See Select and Walk.

When you duplicate an elevation, section or callout, the source's own row heads the family in Views, with its copies one step in beneath it (a level with several plan views, by contrast, is headed by its own name). Renaming the source renames that row, and the family survives saving and reopening. Deleting the source keeps its independent duplicates as standalone views; Undo restores the family.

The drafting guides use the same words as plan: a matching-end guide reads Extension, and an inferred parallel leg reads Parallel to edge beside it. See Snapping and inference.

To duplicate a section, elevation or callout, open its row's three-dot menu in Views and choose Duplicate. The new view appears in the same group with copy after its name. It looks at the same model, with its own settings and no copied annotations or sheet placement. Choose Duplicate with detailing to copy its owned dimensions, text, leaders, revision clouds, regions, detail lines, tags, symbols, detail components, repeating details and hosted callouts too. The copies have their own identities and belong to the new view; changing them leaves the source untouched. Bound dimensions and tags still follow the same model elements. Sheet placements are never copied, and one Undo removes the whole duplicate. Its marker starts beside the original. Choose Rename view to give either view a name, then click its row to open it. Each view can go on its own sheet.

Materials have separate 2D graphics: Shading for visible faces, Surface pattern and Surface colour for face patterns, and Cut pattern and Cut colour where the drawing cuts them. Edit these in the Library's Materials tab. Auto restores the source material's default, and None removes a pattern. Face finishes and view filters can override the material in a view; a filter's cut colour takes precedence over the material's cut colour. Window glass follows its glass material's shading too.

Select a callout and use Line style in Parameters, the same list as lines and hatches. Its boundary, leader and bubble outline use that colour, weight and pattern on the parent view and in PDF and DWG/DXF; the reference lettering keeps its annotation ink.

Each drawing fits the model it shows on its first opening and remembers its pan and zoom when you return to it, including in Split. Editing the model keeps that framing. Loading or refreshing opens the plan at its remembered content view, or fits the loaded content into the clear canvas area; see Moving the camera.

Glass that the section plane cuts through draws as a plain outline with no colour: a window, a door's glazing, a curtain wall, a glass railing, a glass stair guard or a rooflight. Glass you look at, beyond the cut, in an elevation or in a callout, takes the colour of its material from Materials (the default glass blue until you paint it), and a rooflight seen from above in a plan takes it too.

A door or window seen at an angle in an elevation or beyond a section cut shows its foreshortened frame and leaf or glazing, and draws the frame as the box the 3D view builds: both faces of each jamb, the inner reveal, and a sill board whose lines are the 3D board's own edges, so it runs out to the depth it projects, ends against the wall where it meets one, follows a custom overhang, and draws one line where two boards meet on a bay's corner. Each sash of a hung, sliding or casement window, each glazing bar and each door leaf stands at its own depth in that box, as in the 3D view, so a sash window at an angle shows its sashes set apart. A bay or bow window draws its projecting panels (a bay's centre and two angled sides, each panel with its thickness, a bow's mullions) and the caps at its head and foot, and glazing bars appear only on the window types whose 3D model has them. Its position follows the opening in the wall, including an offset across the wall and placement on a curved wall. An opening seen exactly edge-on has no face outline to draw. Invalid along-wall or across-wall offsets are refused with an error.

Hovering a placed component highlights the copy under the pointer in plan, sections, elevations and 3D. While you edit inside one copy, selection highlights follow that copy. Choose Align to wall for a view marker and the wall highlight follows the same rule.

Tag previews the tag as you hover over an element in a section or elevation. Click to place it in that view. Select the tag and drag its grip to move its box while the leader stays on the element; one Undo reverses the move. Tag leader ends and Tag end size in Styles set how the end draws and prints.

Where a line drawn in the lighter, hidden pen lies exactly over a line the drawing also draws solid, the solid line is the one you see: the hidden copy is cut back to the stretches that do not coincide, on screen, on a sheet and in PDF, DWG and DXF. This holds for a hidden outline of a shape as much as for a hidden line, and it counts only solid linework that is actually drawn: the edge of a filled area with no outline does not cut a hidden line back. Nothing solid is changed.

To make a section, open the Views tab in the tray, click Add section, then click twice across the plan to draw the cut line.

Drawing a section or an elevation, each point catches wall ends, corners, edge midpoints and alignments with other markers and reads the same words as the Pencil. The leg also leans to run parallel to an edge nearby or to end level with one.

Drawing a callout, both corners catch wall ends, corners, edge midpoints and alignments with the wall ends, in plan and in a section, elevation or callout window, and read the same words as the Wall tool.

Dimensions you draw on a section, elevation or callout are the same dimensions you draw on a plan, with the same end style from the drawing styles. They stay on the drawing they were placed on and print and export with it. Dimensions drawn on a section before this change open as the same kind of dimension. If the wall or opening a dimension measured is deleted, right-click the dimension and choose Re-link to attach each lost end to the nearest corner or edge in that view; if an end has nothing near it, nothing changes.

To check a distance in the open drawing, choose Measure beside Select on the rail. It snaps to that drawing's cut edges and linework, reads each leg and the chain total, and adds no drawing object. Enter or right-click finishes the chain; Escape ends Measure. See Dimensions and setting out.

Reference plane, setting-out point and line, the structural grid and Measure all work in a section, an elevation and a callout. A point you place there lands where you pointed in the model, and the preview follows your cursor on the drawing.

In a section or elevation, Pencil and Circle in Massing snap to visible geometry and draw model geometry on the view's cut plane at the height you pick. Pencil follows the same plane in a callout over that view. Select detail linework in the open drawing and use Flip or Scale, dragging its grip to a snap point; this works in sections, elevations and callouts. With nothing selected, press the line, leader, dimension or note you want and Scale or Flip takes that one. Rotate turns a note's or drafted text's writing with it and Scale sizes it, while Flip and Mirror move the note across the axis and leave the words upright. To draw a structural grid in a section or elevation, click once for its position across the drawing and again for its vertical end. The grid belongs to the model, and its drawn ends are saved for that view.

Roof and Roof features work in an open building section, an elevation or a callout, whether it is drawn from a plan, a section or an elevation. The view stays open. A new roof follows the drawing plane, and a roof feature follows its host face, edge or gutter. See Roofs.

Select a callout and choose Scale in its inspector. Metric detail scales include 1:5, 1:10 and 1:20. The chosen scale is saved with the view and sizes its pens and annotation. A sheet placement that follows the view uses that scale too; you can override it on the sheet. A fitted placement reads Not to scale.

A callout set to Follow parent draws at its parent's scale, so its linework has the same weight as the parent's; give it its own scale and its pens follow that scale as a plan's do. Hovering a curtain wall in a plan callout highlights the wall's linework as it does in the plan. Inside an open callout nothing of its own marker is drawn: its border is the view's crop. Other views' marks, such as a section line that crosses the window, are drawn as the plan draws them, trimmed at the crop's edge, and look selected when you select them. A wall selected in a callout over a plan carries the same two side chevrons and centre curve grip it has in the plan. It keeps them when it runs out through the window's crop, or lies wholly beyond it: the selection is the wall, not what the window happened to draw.

In a section, elevation or callout, a selected element shows the chevrons its plan drawing shows, laid onto the drawing: a window, door, wall, column, curtain wall, lift, railing, roof segment, shelf or duct run each carry theirs, and a chevron that points into the page, towards you, is not drawn. Dragging a resize chevron makes the same edit as in the plan. Selecting several elements, or a closed group, shows no chevrons, as in the plan, and neither does an element the plan gives none, such as a stair.

A Ground point shows in a section or elevation when it stands between the cut and the far clip: its mark sits at the spot, at its level, with the level written beside it, and the drawing's ground line passes through that level there. Select it alone and one chevron above its level mark drags the level up or down; Esc during the drag writes nothing, a level that clashes with another ground point is refused, and one Undo reverses a drag. See The site plan toolbar.

In a callout's parent drawing, press and drag its box or bubble to move the callout. You can also keep using the Move gizmo. A click without a drag selects it, and one Undo reverses a completed drag. The bubble's small grip adjusts the bubble alone.

Aligning markers after turning a building

Select a section or elevation marker and choose Align to wall in Parameters, its right-click menu or its Views row menu. Hover over a straight wall to highlight it, then click. The marker stays in place and turns exactly parallel to the wall; an elevation faces the wall square-on, and its box re-centres on the wall and spans its full length (or keeps the wider width you had set), with its depth reaching the wall, so the drawing shows that face centred. The view redraws, and one Undo restores the alignment. Escape cancels the wall pick.

Flipped on an elevation turns the way it looks through half a turn about its marker line. The drawing shows the opposite face of the building, the marker's arrow points the new way, and the box is the one that direction gives, not a mirror of the old one.

On the four compass elevations made together, Align set to wall turns the set together, keeping the four directions at right angles. When the building's walls have a clear common orientation, Align to building does this without a wall pick. Depth, near clip and Flipped stay as you set them.

Elevations can show material colours and surface patterns. A wall with panelling draws each frame on the face the elevation looks at. Rooflights draw separate frame and glass fills over the roof, while windows and doors sit over the wall fills and patterns, while the wall's own lines run on across the top of their sills and frames. The Styles row sets the surface hatch colour (setting the colour alone is enough) and the ground pattern. A mass painted face by face shows each face's own paint from each side. Every element that draws a colour has the same Show in 2D switch in its Face finishes section; switching it off draws that element as plain paper in the elevation and section. Where one element stands in front of another, the nearer fill sits on top, even when the far element runs back into the drawing like a rafter or a roof slope; in plan, a painted mass draws its own paint, or its group's.

Fine lines and surface joints stay crisp as you zoom, keeping their intended lightness. Dense joint patterns fade together as you zoom out, keeping the overview calm, and they stay drawn at every zoom. Zoom in to see their joints; print and export use the full pattern with its paper pen weight.

A section drawn on the plan also shows in any other section, elevation or callout it crosses. Its divided head, chain-dot line, ink and hover and selection feedback use the same marker as in plan and on a sheet. Click the head to select it, and drag it along the drawing to move it; selected, it also shows a grip at each end of its line. Drag the top grip or the bottom grip along the line to shorten or lengthen the marker's run; an end lands exactly on one of the level lines this view draws when you release near it, and each drag is one undo step. The first time you drag one, the marker's own view stops following the building in width and keeps the crop it has. Flip view in the selection bar flips the marker as it does in plan. The plan also offers the grips that turn the cut and adjust its extent, and the depth lines. Escape during a drag puts it back. Selecting or dragging it never opens its view: open that from the Views tab. On a sheet, the marker responds to hover and selection too; move and resize the viewport using the sheet's controls.

Select a section or elevation marker to see its field of view. The green chevrons on the box's sides make the drawing wider or narrower. Each side stops just short of the opposite side. The red chevrons set the near and far clips: where the drawing starts and how far it looks in the direction the marker faces. Each clip line follows its chevron. Resize cursors turn with the marker and the plan; moving the body shows the four-way Move cursor.

Until you change an elevation's crop, its box stays in front of its marker: it is centred on the marker's head and wide enough to take the whole building in. If the walls move, the box follows them and the marker stays where you put it. Drag a green chevron and the box is yours, and stays exactly as you left it.

Drag a marker's body or choose Move to carry its head, box, clips and crop together. Arrow keys, typed moves, copies and moves inside a group keep those parts together too. Turning a marker about its centre turns the same field of view with it. One Undo restores a move.

A callout's box and its drawing share one crop. Open the callout and drag a green side chevron to change its width. Moving the whole callout carries its box, head and crop together; dragging the head's own grip adjusts its leader layout.

To adjust a level marker, drag either end. The same end of every building level in that drawing follows; each opposite end and head jog stays where it was. Level lines and their values follow each level's stored elevation. A level's name and value are knocked out of any hatch they stand on, on screen, in a PDF and in a DWG or DXF, so the figures always read clean. Click a level value to type its height relative to the project datum. A typed height is never held back: type a level past its neighbour and the two change places, while dragging a level line or its Floor level slider stops one metre short of its neighbours. Only that level and what it hosts move; deleting a level leaves the other lines at their fixed heights. Enter commits and Escape cancels.

What you switch off under Model categories for a section, elevation or callout is gone from that drawing everywhere it goes: the open view, a sheet it sits on, a callout taken from it and the DWG or DXF export. Doors and windows leave with their wall, and a line weight or colour you set for a category is carried to the sheet and the export too (a colour too close to the paper prints in black ink).

Right-click a wall where a section or elevation cuts it and choose Edit profile to reshape its elevation. A drawing facing the wall square-on keeps the profile in that drawing, with its layout, pan and zoom. A drawing looking obliquely or along the wall opens the wall elevation pane beside the 3D model. See Editing a wall's profile.

To hide something in the current drawing, right-click it and choose Hide, which hides it in that drawing alone, or Hide in view, then Element or Category. The eye beside it in the outliner is the switch for every view. The view keeps that choice for its sheet drawings and exports. In the tray, open the Views row and click Edit view range.... Unhide all in view restores the elements and categories hidden in that view. Each hide or unhide is one undo step.

Select a wall or railing in a section or elevation and a grip appears on each end that runs across the drawing. Drag it to lengthen or shorten the run along its own line; the end lands exactly on a cut edge or point you aim at, or you can type the new length with a unit and press Enter. Zero, negative and below-minimum lengths, and a typed end that crosses the fixed end, leave the run unchanged and show a reason. Escape puts the run back, and one Undo reverses the change. A run seen end-on, a locked run and one inside a group show no grip.

Choose Wall or Beam in a section or elevation and click in the drawing. The point snaps in the view and lands on its cut plane, with its height read from the view. To place a Door, Window or Opening, move over the wall face visible in the drawing and click. The preview and the placed opening use the height in that drawing, including upper storeys the view shows. For a Balcony, Pier or Foundation (the strip footing), click the visible wall face: it goes on that wall, on whichever storey the wall belongs to. For a Rooflight or Dormer, click the visible roof face; its preview and placement follow that face at the height shown. The preview shows green where the item can go. It keeps its direction down the slope as the pointer crosses a hip, and Space turns it a quarter at a time; the placed item matches the preview. For a Pad foundation, hover over a visible column to preview its pad, then click: the pad belongs at the column base, including on an upper storey shown by the drawing. Clicking that column again selects its existing pad. A callout follows its parent view. Enter a group or component before placing on one of its walls. Drag a wall's vertical end edge to slide that end along the view; it keeps its depth behind the cut.

To add a note in an open section, elevation or callout, choose Text on the rail and click in the drawing, then type. With Leader on, click the arrow tip, then the elbow, then the text position. Press Enter or Esc after the first or second click to put the text at the pointer now, keeping the arrow and elbow you placed. The note stays with that view; select it to show its leader grips.

Duplicate, Paste and Make Component work in a section, an elevation or a callout window on the elements the drawing shows. A duplicate or a paste lands in place, on the level the drawing is cut from, is selected, and takes one Undo to reverse; an element the drawing does not show is named and left alone.

To add a roof accessory in the building drawing, open Roof features, choose the accessory and click the roof shown in the section, elevation or callout. Fascia, soffit, barge and gutter follow a roof edge; a downpipe attaches to a gutter. The placement snaps in the drawing you are looking at, and the tool stays in that view.

Drawing one

  1. Open the Views tab at the top of the tray.
  2. Click Add section, Add elevation or Add callout, at the foot of its group. If you're in 3D, Linea switches to Split so the plan is on screen. In a callout over a plan, Add elevation places the marker there and the callout stays open. Add section, and either button inside a section, an elevation, a callout over one or an Edit profile view, take you to the plan of the level that drawing belongs to first, since a section line is placed on a plan.
  3. For a section, click twice to draw a line across the building; arrows preview which way it looks. For an elevation, click to drop the marker outside the building; the status line then reads Click to set the direction the elevation looks, and the arrow turns with the pointer until you click again. For a callout, click two corners of a rectangle on the plan.

Sections and elevations are named for you, Section <ref> and Elevation <ref>. You can draw a callout on a section, an elevation or another callout as well as on a plan.

Opening one

Right-click a view row with a three-dot button to open that same menu at the pointer, including the menus for sections, elevations and callouts.

Click the drawing's row in the Views tab. The list is grouped the way Revit's Project Browser is: Floor Plans, Ceiling Plans, Foundation Plans, Roof Plans, Site (Site plan and Location plan), Elevations, Sections, Callouts (filed under the kind of view each was drawn on), 3D Views, Renderings, Schedules, Legends, Drawing register and Sheets, each heading folding away. From 3D, picking a view takes you to 2D first. In Split, a section or elevation also turns the 3D camera to frame it. The label at the top right of the canvas names the view on screen.

Which groups appear depends on the drawing. A drawing that is not filed in a project lists all of them. A site slot lists Site (Site plan and Location plan), Site Sections (its section markers), Street Scenes (its elevation markers) and Callouts, with no floor plans. A building slot lists Floor Plans, Ceiling Plans, Foundation Plans, Roof Plans, Elevations, Sections and Callouts, with no Site group; when it holds more than one building, each building type has its own group of floor plans, headed with the building's name. 3D Views, Renderings, Schedules, Legends, Drawing register and Sheets are in both.

The small square before a view's name says whether it is on a sheet: filled when it is (hover to see which, click to open that sheet with the drawing selected), hollow when it is not. A view sits on one sheet. Open a sheet in the Sheets group to see the views placed on it.

Escape lands placed drawing work and leaves its live leg, then puts an idle tool down, then clears the selection. Inside an outline or profile action, repeated Escape keeps that action open: use its tick or cross to finish or cancel. You stay in the section, elevation or callout window throughout. A line, polyline or arc drawn here shows its angle as you go, against that view's own lines and the nearer axis, exactly as it does in a plan. To leave it, pick another row in the Views tab.

What you draw in a section, elevation or callout snaps to what the drawing shows: the cut edges, the level and grid lines, the corners it lines up with, the drawing's origin and the lines you have drawn in that view. Anything beyond a callout's window or a section's crop is out of the drawing and is never a target.

Line weights ease as you zoom out in a section, elevation or callout, including lines you draw in the view, keeping closely spaced lines legible and heavier pens above finer ones. Thin Lines in Display remains an optional fine-line drafting aid, as in plan. Sheets, PDFs and DWG or DXF exports keep true pen weights. Depth fades projected linework from the nearest drawn content, so moving a section or elevation marker further from the building does not fade the nearest facade. Switch Depth off for full-strength projected linework.

On the plan, double-click a section's or elevation's marker head to open its drawing, as you do a callout's. A selected marker offers Flip view on its pill. A new section or elevation looks 15 m beyond its line. With a marker selected, a dashed line shows a near clip set above zero. Opening a callout window puts what you had selected on the plan aside, and leaving it brings that selection back, as a section does.

What a plan shows

A floor plan is a horizontal cut through the building at the chosen level. The cut starts 1.5 m above the floor. The fabric it cuts draws with a heavier outline and its cut fill; visible fabric below it draws solid, in thinner projection lines, down to the view depth. The default view depth is the plan's own floor level.

A window through the cut has a paper fill and solid frame lines. A low window draws in projection, and a high window above the cut draws dashed. A plan whose cut is below a roof draws nothing of that roof (no edge, ridge, hip or valley); its rooflights and the steel beams above still draw dashed on the storey directly beneath them, following their height in the model. Rafters, purlins and trusses go with the roof. A reflected ceiling plan looks up instead: it draws the roof, its rafters, purlins, trusses and beams and its rooflights, solid. A mass above follows the same dashed convention on the storey directly below it. A column passing through several storeys is cut wherever each plan's cut plane crosses it.

A ceiling plan looks upwards from its cut plane towards the ceiling, with the drawing facing the same way round as the floor plan. It draws the roof above, its rafters, purlins, trusses and beams and its rooflights in solid lines, and no floor below. A foundation plan shows the foundations within its depth below the floor. A roof plan looks down on the roof, showing its edges, ridges and roof fittings in solid projection. Each plan keeps its own view range, crop, template and visibility settings, which its sheet drawings and exports follow.

To duplicate and rename a plan view

To add a plan, click Add floor plan, Add ceiling plan, Add foundation plan or Add roof plan at the foot of its group. The pop-out asks which level the plan is for, even when only one is available. Foundation plans offer below-ground levels. Pick the level and the new view appears in its group; click its row to open it or drag it onto a sheet. Levels that already have that kind of plan are left out of the add list. When every eligible level has one, the pop-out says so and the existing rows remain available to open.

A floor plan, foundation plan, ceiling plan or roof plan is a view of a level, and a level can have as many as you like: a fire plan, a setting-out plan, a demolition plan, each of the same ground floor. In the Views tab, right-click a plan's row, or open its three-dot menu, and choose Duplicate view. The copy appears directly beneath the original as Ground Floor - Copy 1, opens, and its name is ready to type over. Rename view does the same for any plan view, and double-clicking the name works too. Every drawing starts with a ceiling plan of its ground floor, listed under Ceiling Plans showing the ceilings, with the lay-in grid where a ceiling type has one. Open it, rename it or duplicate it like any plan view. Delete it and it stays deleted: Linea makes the ground-floor one once per drawing and never again. Add ceiling plan at the foot of the group makes one for any other level. A ceiling plan goes on a sheet like a floor plan: drag its row onto the page, or pick it in the region's Drawing list, where it reads Ground Floor (ceiling). Its caption reads Ceiling ยท Ground Floor.

A duplicate starts with the original's scale, crop, view range, detail level, phase, view template and hidden elements, and from then on is its own view: change any of them in the copy and the original is untouched, and the other way round. The model is shared, so a wall moved in one plan is moved in the other. What you draw in a plan view (lines, text, dimensions, leaders, revision clouds, filled or masking regions, tags, symbols, detail components, repeating details and callouts) belongs to that view alone and does not show in its twin. Plans from before this existed keep their drawing in the first plan of each level. Duplicate view copies settings without annotations. Duplicate with detailing also makes independent copies of everything owned by the view, including hosted and nested callouts. Bound dimensions and tags still refer to the same model elements. Neither command copies sheet placements. One Undo removes the whole duplicate.

Delete view removes a plan view, whichever it is, along with what was drawn in it and its place on a sheet, after asking. The level and everything built on it stay. Duplicate level is a different command, in the Levels tab: it makes a new storey.

Working in a ceiling plan

Open a row under Ceiling Plans to work on the ceiling above that level. The ceiling is reflected onto the floor, so the drawing stays the same way round as the floor plan and the walls and grids line up between views on a sheet. It shows the cut walls, ceiling outlines, lay-in joints and ceiling fittings.

Draw lines, polylines, rectangles, circles, arcs, revision clouds and regions, place dimensions, text, leaders and tags, and use the Modify tools in the same way as on a floor plan. A distance you type into a bound dimension changes the real model distance. What you draw belongs to that ceiling view; Duplicate with detailing makes independent copies of its annotations. Put the ceiling view on a sheet, or export its PDF or DXF, to take that view's drawing with you.

To give a callout its own view range

A callout on a plan follows its parent's view range until you tick Own range in the View range modal (the tray's Views row). That copies the parent's range onto the callout, and the fields then change the callout alone. Untick it to follow the parent again. A callout placed on a sheet refreshes when its owning plan's view range or view template changes. A callout also follows that plan's scale, one step finer, unless it has its own scale. Older callouts without a saved plan owner follow the first floor plan of their level.

To give a view a view template

Select a section, elevation or callout marker and open its properties. View template takes None or one of your templates. While a template is assigned, each setting it includes (scale, detail level, depth cue, show services, annotation density, annotations, model categories, phase filter, view range) shows the template's value and stays live: changing it makes that one setting the view's own, marked by Overrides template, and Reset to template hands it back. Clearing the assignment brings back the view's own values. Level plans and sheet viewports have the same picker. Changing the display describes the templates window, including Apply to current view and Apply to views..., which make the views you pick follow the template from then on, so a later change to the template reaches them. The Views row in the tray has a This view picker that names the template the open view follows and changes it. A sheet region takes the included scale and phase filter only.

The two crop regions

A section, elevation or callout window has two crop regions. The solid outline is the model crop, and it clips the model. The dashed outline around it is the annotation crop: dimensions, tags, symbols, notes, detail lines, the heads of callouts nested in the view and the level and grid markers that sit wholly inside it draw in full, and one it cuts is hidden. It starts 12 mm of paper beyond the model crop, whatever the scale, and each of its eight grips drags like the model crop's. It can't go inside the model crop; drag it in and it snaps back to the model crop's edge. The annotation crop is linked to the model crop: change the model crop and the annotation crop follows it. The moment you drag one of the annotation crop's own grips it comes apart from the model crop and stays where you put it, so pulling the model crop tighter leaves the labels around the drawing visible and pulling it out pushes the annotation crop out only as far as it needs to go. Re-link to view crop, beside the Crop annotations tick in the view's properties, snaps the annotation crop back to the model crop and links them again; it is unavailable, with the not-allowed cursor, while they are linked. With Crop frames on, the dashed outline and its grips appear as soon as a plan, section, elevation or callout opens, on a building or a site. An AUTO crop is an editable proposal: until the view has an explicit model crop, it hides no annotation. Untick Crop annotations in the view's properties to draw every annotation of the view uncropped. A plan has the same two outlines and its properties carry the Crop annotations tick. A sheet, a PDF and a DWG or DXF follow the same two crops.

Hover either outline, in a plan, section, elevation or callout window, and it darkens slightly and two icons appear just inside the outline's top-left corner. Hide stops drawing that outline and its grips while the region keeps cropping. It is saved with the view, it is one undo step, and hovering where the outline sat brings the icons back so you can show it again. Disable switches that region off so the view shows uncropped, which is handy for checking what the crop is holding back. It lasts until you leave the view, so coming back finds the crop restored, and it is never saved and makes no undo step. A sheet, a PDF and a DWG or DXF always follow the saved crop. Each icon toggles back. Open Display in the menu bar and hover or click 2D for its settings flyout. Unhide crop regions, under Crop annotations, is ticked when none of the open view's outlines is hidden. Tick it to show them again; untick it to hide both.

To give a view its own phase

Select a section, elevation or callout marker and open its properties. Phase filter takes Follow drawing, Show all, Existing + new, Demolition or New only. Existing + new hides demolished work, Demolition shows existing and demolished work, and New only shows new work. Only that view changes. Follow drawing is the default: the view takes the drawing-wide Phases shown setting and keeps following it when you change it. A sheet viewport can be set the same way, and a viewport's own choice wins over its view's. View markers, grids, levels and view annotations have no phase status of their own; their symbols keep their normal ink.

A section also shows in the other section, elevation and callout views it crosses. Where another section's cut line passes through the view you are in, a chain-dot line runs across it at that place, over the height of the cut, with the section's head (its view number over its sheet number) at the top end. The head is drawn exactly like the plan marker, at the same size for the drawing scale, with its arrow pointing left or right. Clicking its head selects it and keeps you in the current view. Its grip slides the crossing section along the drawing. Open the section from the Views tab. Drag that section in the plan and the line follows. Elevation markers do not draw in other views.

A stair with tread numbers switched on carries the same numbers into a section that cuts it, one at each tread the line crosses, at that tread's height. A stair with numbers off shows none, and an elevation in front of the stair shows none.

Putting one on a sheet

Switch to Sheet and drag the view's name from the Views tab onto the page, or click its hollow box. Adding views to a sheet has the detail.