Sculpting terrain
Sculpt terrain raises, lowers, flattens and smooths the ground with a brush.
In plan and 3D, nearby model points can catch the centre of the brush on the ground. The brush ring follows the same centre as the stroke.
Ground point sits on the same bar, after Smooth. Pick it to set the ground to a level you type at the spot you click, without leaving Sculpt terrain; pick a brush, or press Esc, to go back to your last brush. See The site plan toolbar.
Opening a site slot waits for the site and its placed houses behind one spinner, frames the camera once, shows the site plan and leaves the Site row on Sculpt for a new site, or on the last tab you used in that site other than Plan. You can draw the terrain perimeter here without starting site drafting.
These tools are in a site slot, and in a drawing that is not filed in a project. A building slot has no terrain, plot, road or planting tools; its Site row reads Import site slot and links the building to a site slot in its project.

- On the Site row's Sculpt tab, click Sculpt terrain. The first time, Linea builds the ground inside your perimeter in one undo step.
- Choose a brush in the bottom toolbar: Raise, Lower, Flatten or Smooth. The session opens on Raise.
- Click and drag over the ground, in 3D or on the site plan.
The brush works on the plan with the site open, with no 3D view beside it: a ring shows its size where you point, and a plan stroke shapes the ground exactly as the same stroke does in 3D, in one undo step. The brush also works on a section, an elevation and a callout: drag along the ground line the drawing shows and the terrain changes where the cut passes through it, with the line updating as you go. It works on a wall's elevation too: arm the brush first, then open Edit profile on the wall, and drag along the ground line at the wall's foot. One stroke is one undo step. The brush snaps to nearby points on the drawing and holds a snap it has caught steady through small movements of the pointer. Hold Alt to turn snapping off while you sculpt.
Under Brush, set Size (m), Strength, Softness and the shape, Round or Square. With Flatten active a Target slider appears (-50 to 50 m) with an eyedropper to pick the height from the ground. Level terrain levels the ground to the target height, undoing any sculpting, and Clear terrain removes the ground. Each is one undo step. Faces made from an import and buildings brought in from a map follow the ground when you build or sculpt it, in that same step; one you have lifted, moved or locked stays put.
Existing ground
Mark as existing ground stores the current terrain as the baseline, and a readout then shows Cut, Fill and Net. Reset to existing ground returns the ground to that baseline; Linea asks first, and undo brings it back.
If the ground can't be read
If a site's saved ground can't be read, sculpting is switched off and the Sculpt tab says so at the top. Rebuild from survey or Discard ground there replaces it; see Terrain from a survey.
Terrain settings
The Settings tab's Terrain section has Grid spacing (100, 250, 500 or 1000 mm), Contours with a Labels tick and an Interval of 0.5, 1, 2 or 5 m, Cut / fill, Base depth (mm) and a Rebuild button. Contours, Labels, Interval and Cut / fill are saved with the site, one undo step each, and apply in 2D plans as well as the 3D view; sheets and exports draw the site as it was saved. In plan, Cut / fill tints the ground that is now higher than the existing ground (fill) or lower (cut), once the site has an existing-ground baseline. Labels is on by default: the heights are written along the main (index) contours, and on a gentle site with no main contour long enough to carry one, along the ordinary contours instead, so a site with contours always reads its heights. Untick Labels and the plan, PDF and DWG exports draw the contours unbroken and unlabelled. An elevation and a site section draw the ground too: its profile as one continuous line, and its contours at the site's Contours and Interval settings, hidden wherever the ground in front of them stands in the way.