Drawing with the Pencil
Pencil draws lines on the ground or on a face, and closes them into faces. A line between opposite corners, or a corner and an opposite edge midpoint, divides the inner face of an offset too, including nested offsets and vertical faces.
Switch between plan and 3D after placing the first point of a Pencil run, Arc, Rectangle, Circle or Polygon and carry on from that point. The preview follows the pointer in the new view. Wall and Dimension keep their first point too.
In 3D, select a loose model line or polyline to show its corner grips. Drag a grip to reshape that corner on the line's authoring plane; the other corners stay put. This also works inside an entered group or component. The grip catches nearby model geometry and uses Snap amount between catches. Escape cancels the preview, and release makes one undo step.
Draw a line across an opening in a solid, to its corners or to points on its edges, and the flat loop it closes becomes a face joined to the solid, with the edges already there counting. Close the last opening and the solid is whole again. One Undo removes what the line made. A line that closes nothing, or runs along an edge, stays a line.
Enter or Escape ends the run and keeps its placed edges, leaving out the live leg. One Undo removes a landed run. On a captured drawing, both keys close the placed points into the same face when there are enough points.
In a section, an elevation or a callout on a section, Massing Pencil draws model lines on the plane that view has set: see Setting a plane to draw on, below. Close a loop to make a massed face, ready for Extrude. A callout over a plan draws on its plan's level, with the same clicks and snapping as the parent plan. Draft Line belongs to the view alone, and draws straight on it.
Edges and curves without faces remain selectable. Plan, section, elevation and callout all draw their projected lines, along with the lines that divide a face and the rings Offset leaves on one, so what you draw in a view shows there at once and in 3D. Clicks, window and crossing selections can reach them there. In 3D, click a wire inside a closed group or component to select the whole; enter it to select the edge itself. Lines inside an entered component can be picked on its storey, and Shift-clicking a selected line removes it from the selection.
Free Pencil lines can carry a different height at each vertex. Move and Rotate in plan keep those heights. Planar Offset, Mirror, Trim, Extend, Fillet and Join refuse these lines with a message because their plan geometry would flatten the heights.
- Switch to Massing and click Pencil, or press L.
- Click the ground or a face to start a line, then click to add points.
- Close back on the start and the outline becomes a face. Land on a face's own edge and the line cuts that face: a line that runs from edge to edge of a mass face divides it, and the dividing line becomes part of the mass rather than a loose line beside it. Draw the missing side of a mass over an imported map and the face forms (see below).
- Double-click or press Enter to end the line.
Setting a plane to draw on
A section, an elevation or a callout on a section keeps its own drawing plane, saved with the view. Massing Pencil, Rectangle, Circle, Pie, Polygon and Arc land on it, whatever depth it stands at behind the cut. A new view has none, so arming one of them puts Pick a plane to draw on on the shelf, and your next click answers that.
- Hover the face you want. It highlights as Push/Pull's does.
- Click it, in the view or on the 3D side of a split view. A wall's face or a reference plane behind the cut can be picked in the view too.
- Or click This view's plane on the massing bar to draw on the cut itself.
- Draw. A point lands straight behind where you click, so a line or shape stands exactly where you see it, snaps and typed values included. On a mass face it divides that face, the same as if you had drawn it in 3D.
Where the view cuts through a box, click the box in the view and the plane is the cut itself, the same as This view's plane. A thin dashed outline and a small cross mark the plane in the view. To change it, click Set plane on the massing bar and pick again; Escape keeps the one you had. A face seen edge-on in the view reads as a line there, so pick one that faces it. A plan draws on its level and asks for nothing.
A plane picked from a mass face stays on that face: pull the face, move the mass or slide the marker and your next line still lands on it. This view's plane goes with the marker. Turn the marker until the plane is edge-on and the view asks for a new one.
Edit on the plane as you would in 3D. A Pencil line from edge to edge of a face divides it. Push/Pull and Offset take the face on the plane first, even with something standing in front of it.
Closing a face with imported lines
The edges that close a Pencil face belong to that face. Moving or copying the face carries its outline, and changing Base offset lifts both together. A separate line stays independent until face finding uses it as a boundary. A Pencil leg is a model line on no drafting layer: no layer's visibility, lock or print setting reaches it, it draws continuous, and it exports to DWG and DXF on the massing layer, A-MASS. Legs drawn before 9 November keep the drafting layer they were drawn on.
On a site slot, the Pencil sees the imported map's lines as well as your own. Draw a line, or a few, that meet the imported lines at both ends so that together they close a region, and that region becomes a massing face on the ground. You don't have to trace the map: meet it at both ends and the face forms on the closing line.
The imported lines the face runs along become the face's own edge. They're cut at the face's corners and the stretch on the face is removed, so no duplicate line is left lying under it, while any part of an imported line that runs past the face stays as linework. One undo takes the face away and gives the imported lines back exactly as they were. Locks set in the outliner or Layers in the menu bar keep the lines in place while the face forms. Ordinary visible, unlocked drawing lines form the edges; constraint and boundary lines keep their reference role.
The face is an ordinary massing face: it takes materials and extrudes like any other. On sloping ground it lies just above the surface rather than flat at the level, following the slope as one tilted face.
The prompt takes an Angle and a Length, plus a Rise when one applies. Along an existing edge it asks for the distance along that edge. A DXF underlay is magnetic to the pencil; a photograph or other image underlay you trace by eye.
Drawing onto a locked element, onto anything on a locked layer, or into a locked group is refused: nothing is drawn, and the message names which lock stopped it.
Press an arrow key mid-leg to hold it on an axis (right for red, left for green, up for the vertical) and press it again to let go. The lock lets go once the leg is placed, so each new leg starts free. In plan, a leg drawn close to an axis also leans onto it without a key; hold Alt to draw it free.