Trimming and extending
Trim cuts a line back to another; Extend stretches it out to meet one. They work on the lines drawn in a plan, section, elevation or callout window.
A polyline or an arc that came in from a DWG or DXF with a width keeps that width through Trim and Extend, in every piece left behind; a cut across a taper leaves the width the taper had at that point, and an extension holds the width at the end it grows from.
Every Modify tool catches wall ends, corners and edge midpoints with the same words as the Pencil, and the word stays on the cue until the pointer moves on. The Eraser catches nothing: it sweeps.
In Edit Profile, Trim and Extend work on sketch lines wherever the sketch is drawn. With a hosted opening selected, pick a vertical boundary then a jamb to resize its width. To move the opening to a horizontal reference, use Align.
This planar tool refuses free Pencil linework that carries vertex heights, with a message explaining why. Move and Rotate keep those heights.
An arc or circle with its own Segments count keeps a share of it in every piece a trim or an extend leaves, in proportion to the sweep that piece covers, and neighbouring pieces still meet at the same point.
To trim
- Click Trim on the left rail.
- Click the piece of line to remove. Linea cuts it back to the lines that cross it. Hold Alt to click a cutting edge first, then the line.
The line is picked where your pointer is, not at the snapped point. Where two lines lie within a few pixels of the click, the one nearest the pointer is the one cut or extended, and only when they are exactly as near does the one drawn last win. If that line cannot be cut or extended, nothing changes and the status line says why (No crossing edge, or No boundary to extend to); the line underneath is never tried instead.
Arcs and circles are cut the same way, and they cut other lines too. An arc loses the piece under your click, a circle trimmed between two crossings becomes an arc, and a line trims or extends to an arc or a circle at the true crossing. Extend takes an arc out along its own circle to the next boundary.
A polyline is trimmed the same way: click the stretch between two crossings and it is removed, and the polyline splits where the cuts fall. Click beyond the last crossing and the end goes instead. A closed outline needs two crossings, and what is left opens. A polyline is also a cutting edge for everything else, and Extend runs the end of an open polyline on along its last segment to the next boundary.
A line crossing an arc or circle splits it at the crossing. Trim removes the chosen stretch of the piece you pick. Use Weld to join connected pieces back into a curve. Trimming an end leaves the connected remainder together; trimming through the middle leaves separate curves where the remnants no longer touch. Break and Split also separate the curve at the cut.
A line you trim keeps what it is: the pieces left of a constraint line are still constraint lines, and the pieces of a Red line are still the Red line.
To extend
- Click Extend.
- Click a boundary edge, then click the line to stretch to meet it.
Extend stays armed for the next line, keeping the drawing view open.
In the middle of a floor, ceiling, roof, pad, platform or terrain perimeter outline, Extend runs a pink edge on to another edge of the outline the same way: click the boundary edge, then the edge, near the end that should travel. A boundary the edge already reaches is left alone, and a message says so. The edge that shared the moved end follows it, so a closed outline stays closed, and a wall-picked edge that changes becomes a plain line.
Walls, slabs, beams, doors and windows
In a section or elevation, Trim and Extend also move a straight wall end to the boundary you pick. A change that would leave a wall shorter than one millimetre is refused. Doors and windows must still fit on the remaining wall.
In plan, Extend also moves the end of a beam, the edge of a slab and the nearer jamb of a door or window out to a boundary line, including one on a wall built on a lower level that reaches the plan you are on. Trim brings them back to one: hold Alt, click the boundary, then click the slab, beam or opening. A door or window changes width and centre within its wall, and a message names the wall end or the neighbour that stops it. In a curved wall the boundary meets the wall at a point on the curve, the jamb moves there along the curve, and the unit stays flat: its width is the straight distance across its two jambs.
In a section or elevation the same two verbs act on the cut slab, beam, door or window: click the boundary, then the end of the piece. When something can't go ahead, a message says why, for instance a curved edge, a boundary that doesn't reach the edge, an edge that would cross the opposite one, or a locked piece.