Floors and ceilings
Floors and ceilings are drawn as an outline. Arm the tool and the bottom toolbar becomes a set of sketch tools for that outline.
With two points placed by Line, Undo removes the segment and keeps the first point with its live preview. Undo again removes that first point and keeps Line armed. This works before and after switching between plan and 3D; see Undo and redo.
Where an external door cuts a wall that the floor's outline runs along on its inner face, the outline does not cross the opening there. It steps in along the jamb to the door's own frame line (a swing door's frame, or the pane or leaf line of a sliding, garage or pocket door), runs across to the other jamb and steps back out, in plan, on a sheet and in a PDF, DWG or DXF. The floor's boundary, its finish and its area do not change, and neither does the room's boundary or area. An internal door leaves the outline on the wall line.
In plan, click a floor's boundary line to select it. Where a wall runs along that boundary, the wall takes the click first. Click inside the outline to reach the room, furniture or canvas there. You can also select a floor in the Outliner.
Escape leaves the drawing sub-step and keeps every placed outline edge. Pressing Escape again keeps this sketch open too. Before you have placed anything, one Escape cancels the sketch. Use the green tick to finish the action, or its cross to discard it. This also applies while using Edit perimeter or Edit profile. If you are editing a typed value, its first Escape clears the field.
While a floor, ceiling or roof sketch is open, the other tools on the left rail are greyed out and do nothing when pressed. Select, Box select and the tools that belong to the sketch, such as Move, stay live, and the sketch ends only with its tick or its cross. An outline that has not closed shows a ring at each loose end, in plan and in 3D, so you can see where the gap is. A line you drag catches wall corners, as a dragged corner does.
Inside an entered group or component, floor and ceiling grips stay with their turned outlines, and a corner dragged there lands under the pointer. An arrow lock on a boundary drag follows the container's local red or green axis.
You can change view part way through. Go between 2D, 3D and Split as often as you like: every placed line stays where it is, the tool stays armed, and Cancel and Finish stay on the toolbar. Click the next point in the view you've moved to and the outline carries on from the last one, on the same level, and it still finishes as one Undo.
While editing an outline or a hole, Select picks sketch edges. Ctrl-click adds an edge, Shift-click adds one or takes it out and Alt-click takes it out. Drag left to right to select edges wholly inside the box, or right to left to include edges the box touches. A box around the outline selects it all. These gestures work in plan and in 3D. While you draw the box, the edges it would take light up as you drag, and Escape lets go of it.
Corners can be selected on their own. Click a corner to select it; Ctrl-click adds a corner, Shift-click adds one or takes it out and Alt-click takes it out. A box drawn left to right round a corner, or round corners that no whole edge joins, selects those corners instead of edges, and a box drawn right to left still takes the edges it touches. A selected corner shows filled in the same blue as a selected edge. Delete removes the selected corners and joins the edges either side of each with one straight edge; if that would leave fewer than three corners or make the outline cross itself, Linea says so and changes nothing. Escape lets go of them. Corners and edges can be selected together: Ctrl-click an edge beside a selected corner and both stay selected, and Ctrl-click a corner beside selected edges the same way. Shift-click or Alt-click takes out only the corner or the edge you clicked. A plain click or box replaces everything. These gestures work in plan and in 3D.
Move, Rotate, Scale, Mirror and Flip work on the selected sketch edges. Move carries whole edges and stretches their neighbours at shared corners. Drag a corner to move just that corner, or all the selected corners if it is one of them. With corners selected, Move, Rotate, Scale and Flip act on those corners and the edges that meet them follow; the other corners stay where they are. Mirror reflects selected corners across the edge you pick, in place. When corners and edges are selected together, every tool acts on all of them, and a corner that an edge also ends at moves once. Mirror then reflects the corners and the edges together in place, since a corner has no copy to leave behind; Delete removes the corners and joins their neighbours, then removes the selected edges that are left. A transform can leave the outline crossing itself. It stays as a draft while you work, the tick goes grey and a note beside the bar says the boundary crosses itself, and the floor or ceiling is not changed until you correct it and click the tick. The floor or ceiling changes when you click the tick; one Undo reverses each sketch transform. In plan, with Move, Rotate, Scale or Flip armed and edges picked, the same gizmos as on any plan selection appear on them: Move's arrows and square, Rotate's ring with its protractor, Scale's box handles and Flip's two mirror lines (picked corners carry them too). A drag previews live, a release is one sketch step, and Escape during a drag puts the outline back. Holes > Edit and Edit shape open the same sketch tools for that hole; Done applies the draft like the tick. Add Hole opens a square in the sketch, and the floor or ceiling keeps its original holes until you finish. Cancel leaves it unchanged. An automatic opening detaches from its stair or lift when you finish the edit.
For a floor, the material's 2D graphics controls its Surface pattern and Surface colour where it is seen from above. Its Cut pattern and Cut colour control the cut material; a built-up floor reads the structural layer's material in plan and each layer's material in section. The floor's own finish and hatch choices still take precedence where they are set. Edit the material from the Library's Materials tab; Auto restores its source default and None removes its pattern.
To change a placed floor slab's level, select it and open Dimensions in its panel: pick the Base level, then drag Base offset to raise or lower the slab from it.

To draw a floor or a ceiling
An alignment guide to a corner or midpoint of the pink outline pins the point exactly to that alignment. With Select armed, dragging an outline edge catches the red or green axis, or the original edge direction, in plan and in 3D. Hold Shift to keep that direction, or type a Distance and press Enter to move along it. Dragging an outline corner in 3D takes Arrow Right and Arrow Left the same way: the corner is held on red or green through the corner before it.
- Click Floor or Ceiling on the Build toolbar.
- Set its type and size in Parameters: a type picker and a Thickness slider for a floor, a type picker for a ceiling with Follows level or Custom height, the same choice a placed ceiling has, and a Height slider (1 to 6 m) when it is Custom height. A ceiling made with Follows level has no height of its own and stays at the top of its level.
- Draw the boundary with Line, Rectangle or Arc, or choose Pick to copy an existing closed drawing shape or connected lines. To follow a wall, click Pick wall, then the wall. Walls and curtain walls are picked the same way, one click each, and a chain of both closes as one outline. The outline lands on the centre line of each wall you pick, and Offset or Edit perimeter takes it to a face from there. Click a picked wall again to take it back.
- Close the loop and click Finish. It becomes available once the loop is closed.
- In the Level and offset prompt, choose the Level and an Offset, then click Confirm.
With Rectangle, click the first corner and move towards the opposite corner. Two side dimensions show the live length and width in plan and 3D, and Width and Depth in the status bar track them. Type both sizes, such as `3200,1800`, or use Tab between the fields. The preview follows the typed size; press Enter to add that rectangle to the outline, then use Finish as usual. Escape clears the pending rectangle and its dimensions. Switching between plan and 3D keeps its first corner so you can choose the opposite corner there.
One floor can have several separate footprints. Draw each closed boundary in the same floor sketch, then click Finish once: all footprints share one floor, level, offset, thickness and type. A closed loop inside a footprint cuts a hole. The floor's area adds its footprints and subtracts their openings for the net surface. Edit perimeter reopens a floor with separate footprints and their holes together.
Start a floor outline on the top of a mass, or on a point you've snapped to on one, and the prompt opens on the level you drew on with Offset set to that height.
Select a placed floor or ceiling and its Dimensions section holds Base level and Base offset. Base offset is how far the floor's walking surface, or the ceiling, stands above its level. Pick another storey under Base level and it is measured from that storey instead, and it moves when that storey's height or elevation changes. Base level is also in Parameters with the Floor or Ceiling tool armed, before you draw: pick another storey and the outline is sketched at that storey's height and lands there, still on the storey you are drawing on. Picking the storey you are drawing on clears it. A ceiling that follows its level reads its height there; give it a Base level and it keeps that height as its own.
Each tool is one shot: once you've confirmed, it disarms. Along the sketch toolbar you'll also find Select, Join corners, Offset, Trim, Join at corner and Cancel. Align and Split are on the left rail.
A floor seen from above takes its Face finishes in plan. With Match 3D on, the floor's material brings its drawn pattern (boards for timber, tile coursing, brick bond) at real size, so a 150 mm board draws twice as many courses as a 300 mm one; set a Surface pattern, its colour or a Background fill to change it, and clear an override to return to the material. Show in 2D off draws neither. The same pattern prints, goes on a sheet and exports to DXF as linework on the floor's pattern layer.
To edit one afterwards
Select several floors, or several ceilings, and the panel edits them together. A setting they share shows its value, one they differ on reads Varies, and a change goes to every one of them in a single undo step. Perimeter and Holes belong to one floor at a time.
Select the floor. Its panel has a Perimeter section with Edit perimeter (in the plan, double-clicking the floor opens it too), a Holes section where Add Hole opens a square hole draft, and floor presets Sunken, Thin, Standard and Thick. A Hatch section sets which hatch material the floor draws with: in section, and over the floor in plan.
While you draw a new floor the pink line sits at the floor's creation offset, because the offset is still being decided. Edit perimeter and Edit hole on a floor that already exists draw the pink line exactly on that floor's own top surface, at its real height, so snaps land on its edges and on what surrounds it there. Ceilings, roofs, pads and platforms behave the same way when you edit their outline.
A selected floor, ceiling, roof or room carries a faint blue tint over its whole area in plan, so you can see it is the one chosen; the tint is for the screen only and never appears in a PDF, a DWG or a sheet. A selected floor or ceiling has a chevron on each edge to move it, and Edit perimeter to reshape the outline. A hole in a floor or a ceiling shows a square at each corner, a chevron at the middle of each straight edge that moves that edge square to itself, and one grip on each arc that changes its bulge. A round hole shows just a centre cross and one radius grip. In the plan, click inside a hole or on its edge to select it, and it shows the same grips; a click on the floor around it still selects the floor. While you drag a grip, type a number and press Enter to set that edge's length, its offset or a round hole's radius exactly. Press Delete while a hole is selected to remove the hole alone; one Undo brings it back. A ceiling has no corner grips: select it, then drag an edge's chevron to move that edge, or use Edit perimeter to move its corners. Every grip keeps the same size on screen however far you zoom, and while you hover or drag one your pointer shows the way it moves.

A locked floor or ceiling stays selectable but draws no grips. Click its body to select it.
A floor with a stair opening in it draws the stair through the opening on the level above. Switch on Cross stair openings in Parameters to add the two diagonal lines across the opening; on a curved or spiral stair the cross follows the opening's outline and is drawn only where the opening is. It is off by default.
Working on the ceiling from its plan
Open the level's ceiling plan under Ceiling Plans in Views. It stays the same way round as the floor plan, with the ceiling's outline and lay-in grid above the cut walls. Click the ceiling to open its panel, then Edit perimeter to work on its outline in that view, or double-click the ceiling to go straight there.
Choose a ceiling light from the Library and click its position on the ceiling plan. The fitting sits on that ceiling's underside at its actual height in the model. Select it and use Move to carry it to another point; Delete removes it and Undo brings it back. A click in a ceiling opening or beyond its edge asks you to click a ceiling.
To give a ceiling a lay-in grid
A suspended ceiling's tile grid belongs to the ceiling's type, so every ceiling of that type shows it. Select the ceiling, open its type with Edit type, and switch on Lay-in grid below the layers. It starts at 600 x 600 mm. Spacing X sets the joints across the ceiling's first edge, Spacing Y the joints along it, anywhere from 100 mm to 3 m, so a 1200 x 600 plank grid is one change.
Setting out decides where the grid starts. Centred sits it in the middle of the ceiling, so the cut tiles at opposite edges come out equal. From origin lays full tiles from the ceiling's first corner, and the cuts fall at the far edges. The grid runs square to that first edge, so a room drawn at an angle gets a grid at the same angle. A joint stops at a stair opening or any other hole, and no joint is set out within 24 mm of the edge, where the perimeter angle sits.
The grid draws as lines on the ceiling's underside in 3D. Sections, elevations and callouts show the ceiling's cut band and real edges, with no grid ticks hanging below its underside. Switching Lay-in grid off keeps your spacings for when you switch it back on.