Curtain walls
A curtain wall is a glazed wall of mullions and panels, drawn between two points.
A selected curtain wall has top and base height chevrons. Drag them to change its height or base; an end constrained to a level keeps that level and changes its offset. Parameters follows the drag, and one Undo restores it. Dimensions > Length holds the start and moves the end along the run. The grid and panels rebuild from the changed dimensions.
Enter or Escape finishes the clicked run and drops its unplaced live leg. The curtain walls already placed stay; one Undo removes the landed run.
The Glass thickness field in Parameters has a 6 mm minimum. Type less and the field uses 6 mm, with one message telling you the limit when you press Enter or leave the field.
At 1:50 and larger plan scales, such as 1:20, 1:10 and 1:5, the plan shows both faces of the glass unit. At 1:100 and smaller it reads as one line. Mullion sections and the frame faces stay visible at both scales.
A curtain wall keeps its facing when a neighbour moves or a room opens and closes. Tap Space to change its glazing side; that choice stays with the wall. Moving a curtain wall also leaves the facing of the solid walls around it in place.
To draw one
- Click Curtain wall on the Build toolbar.
- In Parameters, set Alignment (outer, centre or inner), Height, Panels, Mullion depth, Rows, Base level, Base offset and Placement.
- Click the start, then click the end.
Panels divides the length you draw into that many equal panels, and Rows sets the courses up the height. Leave either blank and it reads Auto. Base offset lifts the base above its floor, and Base level puts the run on another storey. While the base is attached to a floor, Base level is unavailable with a not-allowed cursor, because the floor sets where the run stands; detach the base to pick one.
On a placed curtain wall, Top constraint lists the storeys of the building and Unconnected. Pick a storey and the head follows it, plus a Top offset; pick Unconnected and the Height you type holds the head. A top that would leave the glazing no taller than its base is refused with a message. Deleting a level followed by the top or base keeps the run at its absolute height, including its Top offset. A top following that level becomes Unconnected; a released Base offset can be negative when the run stood below its hosting plane. One Undo restores the level and both links.
When the head follows a roof, a wall opening or a ceiling, the transoms are worked out once for the whole wall and shared by every panel, so each runs as one straight line across them. Rows divides the height the wall had before it was attached, and the spacing counts up from the sill at the distance you set. A panel carries the transoms that sit below its own head, with room for a pane above, so a taller panel has more of them at the same heights and a lower one has fewer. Under Transoms in the same section, choose Per column to let every panel divide its own height, which steps the transoms with the slope, and One run to go back.
Curtain walls draw like walls, so you can type a length and angle as you place them. See Typing exact values. Start one on the top of a mass, or on a point you've snapped to on one, and its base sits at that height.
To change one
Select a curtain wall and drag the chevron just past either end, halfway up, to move that end along the wall's own line, taking the snaps it meets there; the small dot at the end moves it freely. In its grid settings the panel count and the spacing are both editable and each drives the other: type a count and the spacing follows, type a spacing and the count follows.
Give a curtain wall a Type mark (up to 16 characters, such as CW01) in its panel. A tag placed on the wall with the Tag tool prints that mark in plan, section and elevation, and in a DXF or DWG export; with the field left blank the tag reads Curtain wall. The mark belongs to the one run you set it on.
Where it meets something
Where a curtain wall ends on a wall (against its face, in line with its end, or into the side of another curtain wall) the end post stands flush against it and keeps its full depth, with the head and sill stopping on the same line, and the plan draws exactly the same end. A curtain wall that fills an opening in a wall, or follows a roof, has its head tucked under what is above it rather than running into it. To fit a curtain wall to an opening in a wall, draw it standing in the opening, then press Fit to wall opening in its panel: it stretches to the opening's two sides and takes the opening's head, and it stays where you drew it across the thickness of the wall (flush with a face if you drew it flush, on the centre line if you drew it there).
Two curtain walls that meet end to end make a corner at whatever angle you drew, however sharp or shallow. The heads, sills and transoms of both stop on the line that bisects the angle, the glass of each reaches that line, and the plan and a section show the same corner. Between 30 and 150 degrees a post stands inside the corner; outside that the glass meets glass. A corner sharper than about 11 degrees has its point squared off rather than running out to a long tip. A curtain wall with a sloping head, or one filling a gabled opening, meets its neighbour the same way: the sloping head, the rows beneath it and the glass all stop on the bisecting line.
Two curtain walls drawn in line, end to end, are one run. They share a single mullion at the joint, drawn once and centred on it, and the glass on each side runs up to that mullion with no gap between the two.
Curtain walls take the same corner joins as walls. Select two curtain walls, or a curtain wall and an ordinary wall, and Join meets them at the corner or butts a curtain wall onto the wall it ends against. When the selected pair is already joined at a corner or T junction, Unjoin appears in both Parameters and the right-click menu. It separates the joined ends in one step; Undo restores the join. A separated pair offers Join again. Right-click a corner where a curtain wall ends and Unjoin and Join work as they do for walls. See Drawing walls. Dragging either end of a curtain wall, or joining it, leaves every mullion line and door bay where it stands. If you swing the wall round, the lines keep their distance from the end that stays put. Shortening a curtain wall this way removes any mullion or door bay that falls beyond the new end, and Undo brings them back with the old length.
When closing a room, an ordinary wall or another curtain wall can land anywhere across a curtain wall's end face, including either corner. The room keeps the same outline as a midpoint connection.
To put a door in a panel
With a curtain wall selected, Parameters lists Panel 1, Panel 2 and so on, each with Glass, Single and Double. Choose Single or Double and that panel becomes a door with a solid surround, glass and handles. Or arm Door on the Build toolbar, hover a panel and click it; click a door panel again and it returns to glass. A door stops under the lowest transom in its panel's column, whatever height that gives, so the rows you set control the height of the door head. Change the rows, the spacing or drag a transom and the door head moves with it; a column with no transom runs its door up to the head. A panel too low under a sloping head for a door is locked. A door panel is handed like any door: under its name, Hinges side (Left or Right, single doors only) and Direction (Inward or Outward) set which jamb it hangs from and which way it swings, and the plan arc and leaf and the 3D leaf follow. With the curtain wall selected, each door panel also carries two small teal grips in the plan, one on the glazing that flips the hinge side and one beside the wall on the swing side that flips the swing, each a single undo step. In plan, a door panel draws no glazing lines across its opening: the glass stops at the mullions either side and the leaf and swing read as a door in the run. Two neighbouring panels that are both Single doors show a Link as double door switch under the first of them. Switch it on and the mullion between them goes, and the pair draws as one double door with meeting stiles and both swings, in plan, 3D, elevation and section; the panel spacing of the curtain wall does not change, and switching it off puts the mullion back. The switch is not offered for panels that are not neighbouring single doors, or under a sloping head. Door panels are listed, with their size and how they are hung, in a Curtain wall door schedule; a linked pair is one entry.
The frame colour has separate Outside and Inside rows, and so does the Leaf colour just beside it, which colours the leaves of any door bays. Click a swatch and the Library opens on its colours; choose one there, or press Cancel in the Library's banner.
To follow a roof, floor or ceiling
- Select the curtain wall, right-click and choose Attach Top…, or select the curtain wall and the roof, floor or ceiling together and choose Attach Top to Roof (or Floor, or Ceiling).
- If you chose Attach Top…, select the roof, floor or ceiling. Esc leaves the step.
The head follows the underside of the roof, floor or ceiling along the whole run, so a curtain wall under a gable end rakes up into the gable. Where the ridge falls inside a panel, that panel's head has two legs that each lie on their own slope, even when the two sides of the roof pitch differently, and a steep roof is followed up to its limit. It keeps following: change the roof's pitch or height and the glazing moves with it. Attach Base… stands the glazing on a floor instead of the level, and the head stays where it was. Detach Top and Detach Base return the curtain wall to the height it had, and so does deleting the roof, floor or ceiling, with a message that says so. If the roof, floor or ceiling does not reach the whole run, the menu row says so. Edit the roof, floor or ceiling so that it no longer holds the curtain wall and the head or base goes back to the one it had until it does. A curtain wall can follow several roofs and floors at once: its head takes the lowest of them above each stretch of the run, and a curtain wall standing in an opening cut in a wall also stops at the top of that opening, so the head is the lower of the two wherever they differ.
A locked curtain wall stays selectable but draws no chevrons at its mullion and transom lines or at its ends; unlock it to drag them.