Offsetting linework

Offset moves or copies a line at a set distance. The same controls work in site drafting, building plan drafting and every pink outline sketch, including a terrain perimeter, pad, platform, floor, roof and ceiling. Pink sketches use them in plan and in 3D.

A polyline that came in from a DWG or DXF with a width, a taper included, keeps that width through Offset, and so does each piece when the remainder is kept.

In 3D, Massing > Offset also takes a loose model line or polyline. Click the line the cursor catches, point to the side for the parallel preview, then click or type a distance and press Enter. It creates a separate line, and one Undo removes the copy.

Inside an outline sketch, Escape lets go of an unplaced offset without leaving the sketch or removing edges already placed. Repeated Escape keeps the outline open. Use its tick to finish or its cross to cancel.

Region boundaries use the same Offset controls in plan, section, elevation and callout drawings. Their sketch uses the drawing's normal line ink. Finish the boundary with the tick to create the Region.

In a wall's Edit Profile elevation, Offset works on the profile's sketch edges in either pane. If an opening is selected, choosing Offset clears that selection and arms the sketch tool.

This planar tool refuses free Pencil linework that carries vertex heights, with a message explaining why. Move and Rotate keep those heights.

Offset works on lines, arcs and polylines. Press a leader, a line of text or a dimension in a section, elevation or callout and a message says which one it was and that it can not be offset. With no distance typed, click a line to hold it, then the next click sets the distance through that point. That point catches wall ends, corners and edge midpoints with the same words as the Pencil, in plan and in a view.

To offset a line

  1. Click Offset on the site Drafting bar, the building's Modify rail (it works in the middle of a pink outline too, without cancelling it), or the pink sketch toolbar.
  2. Type a distance in the project's displayed unit and press Enter. For example, enter 1500 in a millimetre project for an offset of 1.5 m. You can also type an explicit unit, such as 1.5m.
  3. Choose Copy to keep the original or Move to replace it.
  4. Hover a line, arc or polyline segment. A ghost shows the result on the side your cursor is on. Hold Shift to offset the whole polyline.
  5. Click to place the ghost. Offset stays armed for the next line; the distance and Move/Copy choice remain set for the session. One undo restores the previous state.

Offset to a point

Leave the distance empty and click a line, arc, circle or polyline segment to hold it. Move the pointer anywhere: the ghost passes through the point you are snapped to, such as a wall end, a door or window edge, the base, or another line, and the distance it shows is the perpendicular distance to that point. Click to place it exactly there. Press Escape once to let go of the held line and keep Offset armed. A typed distance always wins over the pointer. This works the same in an Edit profile sketch on a wall.

Offsetting a wall

In a plan, or a callout over one, hover a wall or a curtain wall and Offset shows the new wall at the side of the pointer, measured from the wall's centreline. Type a distance and click to make it, or leave the distance empty, click the wall to hold it and click again where the new wall should pass. The new wall is the same type as the one you offset, with the same thickness, build-up, base and top, on the same level, and carries none of its doors or windows. It joins its neighbours like any wall you draw. A curved wall offsets to a concentric arc. Copy keeps the original; Move carries the original wall instead. A wall inside a group is offered once you have entered the group; until then a click on it tells you so. One undo removes the new wall, and Escape lets go of a held wall.

Press Tab over a wall to take every straight wall joined to it end to end: the preview shows the whole run, one click offsets it, the corners meet at their mitre points, and one undo removes it. Press Tab again to go back to the one wall. In a section, elevation or callout over a section, click a face of the wall and then a side, or type a distance: a real wall of the same type lands that far across, and it shows in the plan and in 3D.

In a section, elevation or callout

When you offset a wall, a floor or a beam from one of its edges in a view, the side you click snaps to the view's own edges and levels, and a typed distance takes its side from where the pointer is.

Open the view and hover a line drawn in it, using the same distance and Move/Copy controls. The result belongs to that view: it shows in that section, elevation or callout window, on its sheet viewport, in its PDF and in its DWG or DXF, and nowhere else. A typed distance is measured on the drawing, whatever the drawing scale. A click on a cut wall, slab or window away from a drafted stroke goes to the section tools. A locked line, layer or sketch refuses the edit and says why.

A line crossing an arc or circle splits it at the crossing. Offset acts on the piece you pick. Use Weld to join connected pieces back into a curve; Offset then acts on the welded curve. In Copy mode, the copies form a separate curve.

Arcs stay concentric. Circles and ellipses can also be offset. Alt suspends snapping while you choose a side. An offset copy of a constraint line or a boundary line is the same kind of line, on the same layer, so you can set out a site from one constraint. The Massing toolbar's Offset keeps its own face and line gesture; see Offsetting faces and lines.