Columns, beams and trusses
Columns, beams, rafters, purlins, trusses, foundations and piers live in one group on the Build toolbar.
For a beam, rafter, purlin or truss, Parameters > Dimensions > Length edits the plan span along its current direction, holding the start (the low or eave end for a rafter). Values below 50 mm are refused. The project units apply.
A structural grid line also has Dimensions > Length. Its start stays put and its end moves along the plan axis; the separately set endpoint heights stay as they are. With Drag all on, aligned parallel grid ends on the same level follow, just as they do for an end drag. One Undo restores the change.
A strip or pad foundation keeps its placement outline visible in the plan you are using. After you place it, that plan's view range decides whether it draws. If it is hidden there, one message tells you it shows on the foundation plan and in 3D. It stays selected so you can change its Parameters. With a hidden foundation selected, Move asks you to open a view that shows it.
Enter a group or component before placing a wall-hosted foundation or pier on one of its walls. An entered wall on the active level can take a foundation, including on an upper storey; a closed group or component keeps its walls together.
Until you paint them, strip foundations, pad foundations and ground beams all show the same mid grey in 3D. Paint one from the Library and it keeps your paint. The plan and section drawing of a foundation do not change.
Build structure from a roof
Select a roof and open Structure in Parameters. Use Add trusses, Add rafters or Add purlins to fill the roof at your chosen Centres, starting at 600 mm for every member kind. The first centre is one spacing in from the chosen set-out end. Set the member width and depth, and choose the start or opposite end for set-out. Trusses and rafters step along the roof; purlin centres are measured along its sloping surface. Members follow gable, hip, shed, gambrel and mansard roof profiles, including pitch breaks.
The seat follows the underside of the build-up's structural core. Structural plane offset moves it perpendicular to the slope; a positive value raises it. The structure follows roof edits and the roof's Base level on other storeys. Copying a roof includes its structure. Deleting it removes its linked members straight away. One Undo restores them all. Remove trusses, Remove rafters and Remove purlins remove that layout.
To reach them
Click Structural items on the Build toolbar. The toolbar swaps to that group's tiles, with a Back tile to return.
To place a column or a grid line
Click Column, then click where it stands. For a structural grid, open a plan, section, elevation or callout, choose Grid line and click to place it. Each end catches wall ends, corners and edge midpoints with the same words as the Pencil, and the line leans to run parallel to an edge nearby or to end level with one.
To span a beam, purlin or truss
- Click Beam (or Purlin, or Truss).
- Click the start point, then the end point. A purlin is level between them; a truss is a King Post truss spanning them.
Draw a column, beam, rafter, purlin or truss from the top of a mass, a wall, a column or a table, or from a point you've snapped to on one, and it rests there: a column's foot, or the underside of a beam, rafter, purlin or truss, sits on that height. Drawn anywhere else, a beam keeps hanging from the storey above and the roof members keep the level you've set.
Select a beam in 3D and a slim chevron stands just past each end, halfway down its depth, pointing out along the run: drag one to move that end while the other stays where it is. The end slides along the beam's own line, so the beam lengthens or shortens and keeps its angle. The chevron keeps the same size on screen however far you zoom, and your pointer shows the way it moves.
In plan, a selected beam, rafter, purlin or truss also has an outward end chevron at each end. Drag one to change the length along its bearing. Matching ends of nearby elements offer a thin dashed teal anticipation guide in plan, and in 3D. A pitched rafter or purlin follows its bearing while the opposite end keeps its height. Release to keep the preview; Esc restores the original length. See Snapping and inference.
To set a rafter
Click Rafter, click the low eave end, then the high ridge end. It follows walls and lines as you click.
To add a foundation or a pier
Click Strip foundation, then click a wall to add a strip footing beneath it; Projection and Thickness are in Parameters. For a pad under a column, click Pad foundation, set Projection, Thickness and Top offset in Parameters, then click the column, in the plan, in a section, elevation or callout, or in 3D: until the pointer is over a column the armed pad floats as a red outline, and the column under the pointer shows the pad it would get, a click anywhere else says “Click a column to add a pad foundation beneath it.” and places nothing, and a square pad lands at its base, wider than the column by Projection on every side, and it follows the column when you move or turn it. Those settings are remembered for the next pad. To tie pads together, click Ground beam (beside Beam) and click from one pad to the next: it is an ordinary beam whose top sits at floor level, so it shows on the foundation plan and joins a pad without a seam, in a section as well as in plan. Deleting the column removes it and its pad straight away, including in a section. The pad goes with it, and one Undo brings both back. For a pier, click Pier, slide along a straight wall and click. In plan, a blue outline shows the projection that will land on a valid wall. Away from a wall the pier-sized outline is centred on the crosshair and turns red; the status reads Hover a wall to place a pier. In 3D, a pier stands proud of the wall's outer face and matches that face's finish. Give the pier a material of its own to use that finish instead. A pier joins the wall’s cut and the hatch of the layer it projects from; a material of its own uses its own hatch with a material junction. Touching projections of the same material form one region; different materials keep their junction. A pier below the plan cut is shown as a projection rather than a cut. For a centred thickening, place matching piers on opposite faces at the same offset. Hovering or selecting a pier outlines only its projection. A pier cannot cross a door or window. A material's cut colour follows its hatch in plans and sections; CAD colour formats are described in Exporting a DWG or DXF.
A pier is picked on its own: click it in plan, in a section, in an elevation or in a callout over a plan and only the pier is selected, not the wall behind it, and that holds when the wall is already selected, as it does for a door, a window, a footing, a balcony and a wall-mounted item (drag one and it moves, not the wall; with several things selected, dragging one of them still moves them all); select the wall to take the wall and its pier together. A selected pier on a straight wall carries chevrons, the same ones a wall has. In plan, in a callout over a plan, in 3D and in an elevation the red chevrons at its sides drag its Width along the wall, and the opposite edge stays where it is. The red chevron on its outer face drags its Projection in plan, in a callout over a plan, in 3D and in a section. The two red chevrons beside its outer face slide it along the wall in plan, in a callout over a plan, in 3D and in an elevation, and in plan it stops at either end of the wall. In 3D, in a section and in an elevation the blue chevron at its top drags its Height, starting from the height the pier is drawn at, and the blue chevron at its bottom lifts or lowers its base from the foot of the wall while the top stays where it is. Plan and a callout over a plan have no blue chevrons. In plan, type a value while you drag to set it exactly. Every drag is one Undo.
Beams, rafters, purlins and trusses take a typed length and angle as you place them, the way walls do. Rafters, purlins and trusses also take a section: select one and set its Profile in Parameters, with Web thickness and Flange thickness in millimetres for I-sections and channels.
A locked beam stays selectable but draws no end chevrons; unlock it to drag its ends.
To set how high they stand
A column's Constraints section in Parameters holds Base level, Base offset, Top constraint and Top offset. Top constraint lists every storey of the building and Unconnected. Pick a storey and the column runs up to it, plus the Top offset; pick Unconnected and the height is a number you type. A top that would land at or below the column's base is refused, with a message, and nothing changes. Select several columns and the one Top constraint row applies to all of them. With Column armed, Base level and Base offset are in Parameters before the column lands, and the preview stands at the height they give. Shelves, cabinets, mechanical equipment and floor air terminals show the same two rows while their tool is armed.
Beams, rafters, purlins and trusses hang from the top of a storey. Their Constraints section has a Reference level, the storey whose top they hang from (their own storey until you pick another in the same building), and the offset below it: Top offset for a beam, Bearing offset for a rafter, purlin or truss.