Aligning elements

Align brings one element flush with a face or line you choose.

During a pink outline sketch, Align takes a straight reference edge, then a parallel straight target edge. The target moves square to the reference until the two are collinear, stretching its neighbours. A curved or nonparallel pair stays as it was and a message explains why. This works in plan, in 3D and in a wall's Edit Profile; there, a selected opening takes a jamb, head or sill after the reference.

In 3D, the pointer catches nearby geometry when choosing a reference face or line. The highlighted reference is the one your click chooses.

In 3D, Align offers planes. Click the reference plane, then the parallel target plane: the target moves along its normal until the planes coincide. A wall's base writes Base offset; its top writes Top offset when it follows a level, or Height when unconnected. Moving a level-bound wall's base keeps its top on that level, and hosted doors follow the wall. Side faces move sideways. Hover shows the plane and the Face word; the highlighted plane is the one your click chooses. Tab cycles a wall's base, top, sides, ends and level datum; a level datum is a reference only. A closed group moves whole. Nonparallel planes are refused with an explanation. Already aligned means the planes coincide within 0.1 mm. Each alignment is one Undo step.

Tags, text, notes, dimensions and hatches are never references: Align takes its references from the model, grids, levels and the lines you have drawn. Drawn lines also move: in plan, a section, an elevation or a callout window, click a drawn line (or a wall face) as the reference, then a parallel drawn line, and that line slides onto it. Click a drawn line first and then a wall, in plan, a section, an elevation or a callout window, and the wall slides onto the line (in a section or elevation it moves along the drawing, never up, since the base of a wall follows its level). A pair that is not parallel is left as it was and the status line says Pick a parallel edge. Press a leader, a line of text or a dimension in a section, elevation or callout and the status line says Align works on straight edges, naming which one it was. While Align or any other tool that picks existing geometry is armed, the pill that follows a selection stays down, so your next click always belongs to the tool. In a section or elevation, Align works on every element the drawing shows, in both directions: along the drawing, and up or down. A rooflight, chimney, dormer, cupola, solar panel or roof vent moves up and down by sliding along its roof slope and stays seated on the roof, and its opening in the host roof updates with the move. Beams, rafters, purlins, trusses, balconies, piers, footings, curtain walls, items, cabinets, shelves, lifts, massing, linework and planting align too. Where an element cannot move on its own (a gutter, fascia, soffit or barge board follows its roof's edge; a downpipe hangs from its gutter; a stair segment belongs to its stair), Align says so, naming the element and the reason.

  1. Click Align on the left rail, at the end of the Modify tools. Hover it and the tip reads Align (AL): typing AL on the canvas arms it too.
  2. Click the reference face or line, then click the item to align to it.

Once a reference is held, your next click is always the thing to align, even if it is itself something Align could use as a reference, such as a window or a grid line. A window moves along its wall onto a held line, a grid line moves whole, and in 3D a railing or curtain wall picked near its end is lengthened or shortened to a held face. To change the reference, click it again or press Escape.

Align is not on the Build toolbar; the left rail and its keyboard shortcut are the two ways in.

In plan, section, elevation or callout, a repeating detail takes part in Align like any other item: click the reference wall face or line, then the run end. The run lights as the pointer reaches it, and clicking its end slides the whole run so that end lands on the reference. When a wall sits close to a drafted edge, click the wall face to use the wall, or click directly on the drafted edge to use that edge.

In a section or elevation, a level line is a reference only where no element edge is under the pointer. When a window head sits a few millimetres under a level line, clicking it picks the window's head, not the line.

An imported DWG or DXF drawing is a reference too. In plan, click one of its lines, ends or corners, then a wall face, and the wall slides flush onto that line. Imported lines are never moved by Align.

In a callout over a plan, Align works as it does in the plan itself: click a wall face or a drawn line as the reference, then a wall face or another line to bring it onto the reference. Hovering shows the same lines, and one undo takes the move back.

In plan, pink guide lines preview the reference along and across a wall, including its ends and centre. Inside an entered component placement, the wall highlight follows the copy under the pointer as you move between copies. In 3D, point at the end of a wall to take that end as the reference, the same one plan takes. In sections, elevations and callouts, you can align to an object's horizontal or vertical centre as well as its edges. A visible reference plane can also be your first pick: click its dashed line, then the parallel face or edge to move onto the plane. Only planes that cross the section, or appear edge-on in the elevation, are offered, within their height and the view's crop. A callout offers the part inside its window. The plane stays fixed, and one alignment is one Undo step. Once you pick a reference, its direction stays held for the second pick.

In a section or elevation, aligning the head of a door or window to a line, a level or another element's edge raises or lowers the head and keeps the sill where it is, so the opening changes height. Aligning its sill, or moving it, carries the whole opening. A head dragged down to the sill, or up past the top of its wall, is refused with the reason.

What moves depends on what you pick. Walls, railings, fences, curtain walls, beams, drawn lines and room separators run between two ends. Pick one by its end, in plan, in 3D or on a drafted line in a section or elevation, and that end alone goes to the line, so the run gets longer or shorter there: its far end stays put, and a wall joined at the end you aligned keeps its corner (its end follows) while no wall is ever carried off whole. Pick a run by its face or centre line against a parallel line and the whole run slides across. Grid lines slide whole, parallel to the line you pick. Doors, windows, furniture and other placed items always move as one piece.

Doors and windows align too. In plan, hover one to see a line on each jamb and on its centre, and click the line you want as the reference, or as the one that moves. A door or window only slides along its own wall: if the line you pick would carry it past the end of the wall or onto another opening, Align says so and changes nothing.

In plan, columns, floor slabs, ceilings, rooms, beams, railings, cabinets, shelves, lifts, mechanical equipment and terminals, duct and pipe runs, fittings, notes, furniture and other items on the floor, and stairs align too. This works inside a group you have entered, even when the group is turned. Hover one to see the faces and centre lines it offers (a slab or ceiling offers each edge, a run offers each leg), and click the line you want as the reference, or as the one that moves. Grid lines and reference planes can be the reference you align other things to. Align moves the one element you click, and a column, slab, item or stair keeps its shape. Piers and balconies slide along their wall, never across it, and a footing or a wall part offers its lines as a reference without moving. Curtain walls align like walls. On a roof, rooflights, chimneys, dormers, cupolas, solar panels and vents move along the roof surface they stand on and stay on their roof segment, and a roof aligns by its plan edges and moves whole. Rooflights and solar panels are measured down the slope, so their faces sit where the plan shows them. Masses align by their plan edges, and plan symbols, trees, flowers and grass by their centre lines. Rooflights, chimneys, dormers, cupolas and solar panels offer their faces as well as their centre lines. Rafters, purlins and trusses align by their plan edges. Fascias, gutters, soffits, barge boards, ridge vents and downpipes offer their eave line to align other things to; they follow their roof and do not move on their own.

A closed group, or a placed component, aligns as one piece: Align offers the faces and centre lines of everything it holds, measured in the group's own turned frame, and moves the whole group. Imported drawings, guide pictures, drawn lines, section and elevation markers, callout boxes and the site boundary line up too. To pick an elevation marker in plan, aim at its visible circle or arrow. A site boundary is a reference only: pick it first to bring something onto it, and picking it as the element gives a reason instead of moving it.