Hatches

Hatches fill a region of a drawing with a pattern. They come from three places: walls and slabs in section, the Region tool, and your own hatch materials.

When editing an outline sketch on a plan, dragging an edge with Select offers the same alignment guides as drawing a leg. Extension marks a matching end and Parallel to edge marks the direction. Release to place the edge, or press Esc to restore it. See Snapping and inference.

Escape leaves the drawing sub-step and keeps every placed outline edge. Pressing Escape again keeps this sketch open too. Use the green tick to finish the action, or its cross to discard it. This also applies while using Edit perimeter or Edit profile. If you are editing a typed value, its first Escape clears the field.

Use Region on a plan, section, elevation or callout to add a hatch pattern or flat fill to that drawing.

Beside Pick, choose Fill area (the paint bucket), then click inside a closed area of the visible drawing. Lines, arcs, polylines and wall faces can form the boundary together. The smallest enclosing area fills immediately, with islands left as holes. An open area explains that the gaps need closing. Pick also makes a closed outline into a region immediately. Region stays armed for another Pick, and no Finish control remains on show. Hold Shift only when collecting several outlines for one Finish.

While a Region boundary is open, the boundary bar's Select picks its sketch edges. Ctrl-click adds an edge, Shift-click adds one or takes it out and Alt-click takes it out. A left-to-right box takes edges wholly inside it; a right-to-left box takes edges it touches. Click a corner to select it on its own, adding and removing with the same keys; a box drawn left to right round a corner takes that corner, and Delete removes selected corners. Move, Rotate, Scale, Mirror and Flip act on those edges or corners in a plan, section, elevation or callout, and the edges meeting a selected corner follow it. The tick finishes the edited boundary. After finishing a region, one Undo removes it. If Region stays armed, the next empty boundary stays ready, and Redo restores the region.

Hatch also works in 3D, using the same drawing plane as Line and the other drafting tools. Point at a face to hatch on it, or start in empty space to take the plane from the view.

A material also carries a drawn pattern for plans, elevations and sections. With Match 3D on in Face finishes, an element takes the pattern its material maps to (brick in a bond at real brick size, tiles and slates in courses, timber in boards) over a background in the material's colour; render, concrete and glass draw plain. Pick a different pattern or background to override either, and choose Auto to return to the material. It is vector only, with no texture image in 2D.

In section

Each layer of a wall type has a hatch material that sets how it draws when cut. The pattern families are masonry, blockwork, concrete, timber, insulation (quilt and rigid), glass, solid and empty (an air cavity). Built-in materials include Brickwork, Blockwork, Concrete, Insulation (rigid), Insulation (quilt), Timber (sawn), Timber (planed), Stone, Screed, Plasterboard, Plaster, Render, Membrane, Slate, Glass and Cavity. Choose them in the Material column of Edit type.

A floor, footing, fascia, barge or soffit has a Hatch section in Parameters (a footing's reads Section hatch, because a plan never cuts one). Pick one of your hatch materials, or a built-in one, and that element's cut hatch uses its spacing and angle in section, and in plan wherever the element is drawn with a hatch (a floor, fascia, barge or soffit). Not specified clears it. A column, beam, rafter, purlin or truss has no separate hatch control: its Structural material list carries the named steel, concrete and timber hatch materials beside Steel, Concrete and Timber, so choosing one sets the material and its hatch together and Default clears both. A cut column or beam hatches in plan; a rafter, purlin or truss shows a picked hatch in plan when the plane cuts it.

Quilt insulation draws as a continuous linked loop, with closely spaced, near-circular bulbs reaching close to both faces of its layer. The loop width and height scale together with the layer's thickness and follow curved walls. Plans, sections, details, material previews, PDF, DWG and DXF use the same shape.

Drawing a region

Choose Pick in the boundary tools, then click the edge of a closed circle, rectangle, polyline or ellipse to fill it. You can also pick separate lines until they close a loop. The outline under the pointer lights pink. An open polyline asks you to close it first. Hold Shift while picking to add more outlines, then press the tick or Enter; an outline inside another makes a hole. The region keeps a copy of each picked outline, so you can move the original shape afterwards.

When drawing a Region boundary with Line, earlier legs can offer a parallel direction and a matching-end guide. The end match reads Extension, with Parallel to edge for the direction. The guide follows the boundary's drawing plane in either pane of Split; see Snapping and inference.

  1. In 2D, click Region in the drafting tools on the left rail.
  2. Before you click, open Parameters and choose the Fill: Hatch, Filled or Masking.
  3. Region opens a boundary sketch in the drawing's normal line ink, on a plan, section, elevation or callout. Draw with Line, Arc or Rectangle, and edit the boundary with Offset, Trim and the other sketch tools. The region is made the moment the outline closes, whether that is a rectangle's second corner, a polyline closed on its first point, an arc closed with its chord or two arcs, with no tick to press, and Region stays armed for the next. The preview clears, and one Undo removes the finished region. To fill several outlines as one region, switch on Several outlines on the sketch bar (it stays on until you switch it off): each closed outline then stays open, and you click the tick or press Enter to fill them together. A boundary with loose ends, crossings or no area keeps the tick unavailable, with the reason on the prompt line. The cross abandons the boundary. Escape never finishes the region: it ends only the leg you are still drawing and keeps everything placed, and pressing it again changes nothing, so the tick (or Enter) finishes and the cross cancels. Before anything is placed, one Escape leaves Region. Choosing the rail's Select or any other tool ends the boundary at once and goes straight to that tool.
  4. Select the region and use the Hatch section in Parameters to choose its fill (Hatch, Filled or Masking) and, for a hatch fill, its pattern, Scale and Angle.

You can look at the model in 3D part way through a boundary. It waits with every point in place, and when you come back to the drawing you carry on from the last one. Open another drawing and that drawing starts its own boundary, because a boundary's points belong to the drawing they were placed on.

Hatch fills the area with a hatch pattern, which you choose from the list beneath the fill. Filled fills it with a flat, opaque colour, which you pick with the colour swatch. A filled region carries no outline of its own on screen or in PDF and DWG/DXF. Use layer colour takes the current layer colour, and the preview, in every fill mode, draws in the current layer colour and follows a change of layer while you draw. Masking hides what lies under it in the colour of the paper; it sits above the model and below annotation, and Show boundary keeps its outline visible. For a hatch pattern or a visible masking boundary, under Boundary, pick a line style to set the outline's colour, weight and pattern; the fill keeps its own pattern and colour. Region works on a plan, a section, an elevation and a callout, and what you draw there goes to the sheet, the PDF and the DWG or DXF with the view. A region drawn in a callout window belongs to that window and doesn't show in the section or plan beneath it. The Line style in the Region tool's Parameters styles the hatch boundary only, and the Region tool keeps that pick separately from the Line and Dimension tools. The pattern keeps its own spacing and angle, and a filled region keeps its fill colour.

The patterns are Tint, Diagonal, Crosshatch, Dots, Brick, Block, Insulation, Aggregate, Batt, Earth and Grid. A selected region shows the same pattern names as the tool. Its Edge style controls the boundary, and Fill line style controls the hatch lines; each has a visible label above its picker. None (hatch default) uses the layer hatch style, then the usual hatch appearance. Fill line style stays visible but unavailable for Filled and Masking regions.

Concrete stays crisp as you zoom, with the same stroke lengths on the sheet and PDF. Concrete (the aggregate pattern) draws as a scatter of short dashes of varying length and angle among small open triangles, with clear paper between every mark and no repeat you can see across a footing at any ratio from 1:5 to 1:100. The Dots pattern is the same scatter of dashes without the triangles. It keeps the same spacing on paper at every ratio, where a line pattern opens out at a detail ratio, and the Styles tray's hatch scale still sets how open it is. In a DWG or DXF it is one hatch, with the same marks.

Your own hatch materials

At the foot of the Material list in Edit type, choose New hatch material…. Give it a Name, pick a Family, set the Spacing (0.5 to 20 mm) and Angle (0 to 180), watch the preview, and click Save. Saving always adds a new entry, and a repeated name is made unique.