Rotating things

Rotate turns a selection about a centre you choose.

Model selections turn in the plane of a section, elevation or either kind of callout. The drawing follows the live turn while you drag, including a mass inside an entered group or component. Release applies the preview as one undo step; Escape restores the selection.

Lines you drew in a section, an elevation or a callout turn the way things turn in the plan. Click Rotate, click the centre, click a first direction, then click where that direction should end: the turn catches a corner, midpoint or crossing, and otherwise steps to your Rotation snap. Tap Ctrl to leave the original and rotate a copy, type an angle for an exact turn, and press Esc to put everything back.

Rotate and Flip carry a Text note's position, arrow tip and elbow together in plans, sections, elevations and callouts. Rotate turns the words with the leader by exactly the angle you give. Scale resizes the Text's box and its words together about the box's centre, and leaves the arrow tip where it points, in every view. A size such as 2m is the Text's width. Flip and Scale keep the words readable, never upside down or back to front, and Flip keeps them at their paper size. With nothing selected, Scale and Flip take the line, note or dimension under your first press.

In a turned building, or inside an entered group, the red and green rings of the Rotate handle stand on that building's own red and green axes, the ones the Move arrows follow, and a tilt follows your pointer around the ring you grabbed.

Forms made with the massing tools rotate freely about any axis: X, Y or Z. A group of forms turns as one object. A group containing a wall or column stays level and turns in plan. In a section or elevation, a form turns in the plane of the drawing, and it is drawn at its turned angle as a live preview while you aim.

During a pink outline sketch, Rotate turns the picked edges about their centre as you drag. In plan the ring and its protractor sit on the picked edges and sweep the angle live. This also works on the sketch lines in a wall's Edit Profile elevation. Picking the wall there means its sketch outline.

A door or window follows its wall. Rotate it exactly 180 degrees about the vertical to face the other way, keeping its position along the wall. Other angles and an in-plane spin are refused with a message; rotate the wall to turn the opening with it.

A footing runs under its whole wall, so it has no turn of its own: rotate or nudge a footing on its own and Linea says so, and nothing moves. Select its wall to turn the two together.

During a floor, ceiling, roof, pad, platform or terrain perimeter outline, Rotate turns the pink loop's selected edges (or the edge you press) about their centre as you drag, or by an angle you type, and the outline stays open.

  1. Select what you want to turn, and click Rotate.
  2. Click to set the centre of rotation, then click to set the start bearing.
  3. Move to aim and click to commit, or type an angle.

A typed angle draws the turn as you type it. Click the centre, type 30, and the selection stands at 30 degrees before you press Enter, in plans, sections, elevations and callouts alike. Move the pointer as you like once the turn has started: the typed angle holds, and Enter commits exactly what is drawn. Enter commits it as one undo step; Escape throws the digits away and puts the drawing back.

In 3D the centre can be any corner, midpoint or point on an edge you can see, at its own height: a table top or an eave catches the same as a point on the floor.

A captured corner, midpoint or crossing sets an exact bearing. Sliding onto an edge still uses your chosen angle step. The angle steps to your Rotation snap (15° unless you have changed it; Snapping and inference has the list), and holding Shift turns freely. Double-click to turn the selection by 90° instead. Rotate works in plan and in 3D, and a closed group turns as one object. It turns the selection on its own storey, whichever level is active. A railing turns with the rest of a selection. In a site slot, a road, path, fence or bin turns with it too: a road turns as one piece, kerbs and centreline together.

With Rotate armed, the protractor is on your pointer at once, with no move needed, and follows it until you click its centre. If the pointer is off the drawing, as when you press the toolbar button, it rests on the selection until the pointer comes back. There is no ring around the selection in the Rotate tool. Click the start bearing, then aim and click or type the angle. You can also skip the bearing: click the centre, type the angle and press Enter, in plans, sections, elevations and callouts. Esc takes the digits and keeps the centre. Type a number before you have clicked the centre and the status line says Click the pivot first, because nothing has been set for the angle to turn about. Inside a turned building or placed component, the protractor, arrow locks and bearing guide follow the axes of the space you are editing.

You can also press and drag instead of clicking twice. The press sets the centre, the drag draws the start bearing, and letting go sets it, so the protractor is ready for the angle: aim and click, or type it. A small wobble under the press stays a plain click. This works in plans, sections, elevations, callouts and 3D, and Esc steps back exactly as it does after two clicks.

In 3D, a mass, a group whose members can tilt, or a free-standing item can turn in the plane of the face under your pointer. A wall face gives an upright protractor; a roof slope gives a sloping one. Over empty space the protractor follows your view: a low view finds an upright plane and a high view finds the ground. The colour names its axis plane: red or green upright, blue flat. Click the centre to hold that plane for the turn, then catch a corner, midpoint or edge for the bearing. A reference off the held plane supplies its projection onto it.

Use → for red, ← for green and ↑ for blue to lock the plane before or during the turn. Press the same key to release, or another to replace it. In plan, the start bearing and the target catch the red or green line through the centre without a key, with the dashed guide; hold Alt to place either one without the catch. After the centre click, releasing returns to the plane you placed. A wall, a hosted door or window and a roof keep a flat protractor. A group that holds walls shows the same upright protractor, but tilting it gives a message saying why and moves nothing; turning it flat still works. A group made of masses tilts as one rigid piece, and one Undo reverses the whole turn.

In a section, an elevation or a callout window over one, Rotate turns the lines, hatches and detail components drawn in that view, and a free-standing item of furniture, about the centre you click. The item goes round the centre and tilts with it, in the plane of the drawing. Click the centre, click the start direction, then click or type the angle; Ctrl at the last click leaves the original and makes a turned copy, and one undo puts it all back. An item that hangs on a wall or a ceiling, and every element drawn in plan (a wall, a floor, a column), tells you where it turns instead and nothing in the selection moves.

In a section, an elevation or a callout, lines, hatches and detail components you have selected carry a ring as well. Drag it to turn them about the middle of the selection, with the angle shown as you go. The turn lands exactly on a point in the drawing (a corner, a midpoint, a crossing) when you aim at one, otherwise it steps to your Rotation snap, and Shift turns freely. You can type an angle instead, and Escape puts everything back. One Undo reverses the whole turn.

If any element in the selection is locked, whether on its own, through its layer or through a group, Rotate leaves the selection in place. Unlock it or take it out of the selection.

A locked object, or one inside a locked group, stays selectable. Rotate cannot change it, including when you have picked only a face or an edge of a locked mass.