Dimensions and setting out

To add a dimension, choose Dimension in the Build toolbar, pick two witnesses, then click to place the baseline offset. In plan, section and elevation, keep picking witnesses to continue the chain; in 3D the placement click finishes the dimension. The toolbar also has tools for marking out positions.

After picking the first witness for a linear Dimension, you can switch between plan and 3D and pick the next witness from the same starting point. The live dimension span follows the pointer in the new view.

A witness picked on a wall's face stays on that face. The figure on the preview is the figure that lands, whichever datum the dimension's Parameters name for centreline picks. In Parameters > Standards, Datum policy re-datums the dimension: Centreline moves face ends to the wall's centreline, Wall face moves centreline ends to the face nearer the dimension line, in one undo step. The control shows the reference the ends use, or Mixed when they differ.

A finite setting-out line has Dimensions > Length: its first point stays and the second moves along its current direction. Points and infinite datums have no finite length to edit. A selected infinite guide shows no end chevrons, since it has no ends to drag; Move and Delete work as for any other line.

For a structural grid line, Dimensions > Length edits its plan extent from the start. Drag all carries aligned grid ends on the same level, keeping their row of bubbles together. A run with coincident endpoints shows a read-only length because it has no direction to extend.

Select an annotation and choose Move, Rotate, Scale or Mirror to see its new position before committing. The same tools work on dimensions, notes, leaders, clouds, callouts and reference lines in their drawing. Copy leaves the original in place. Rotate turns a note's text and its leader attachment together. Tags keep their text upright; Scale resizes that tag's bubble and text. A dimension attached to a model feature keeps that attachment: its free points and placed line can move while its bound end stays on the feature. Moving the model feature carries its bound dimension end with it.

A selected dimension has a grip halfway along each extension line, leaving the measured corner clear. Drag that grip to change the measured point. The grip and its hit target move together, in plan and in a section or elevation. A leader's tip stays at the point it annotates.

Inside an entered group or component, a held axis and a typed distance use the same local direction as the visible guide. Exit the container to resume the drawing axes.

Select a dimension and choose Line style in Parameters, using the same list as lines and hatches. It styles the witness lines, dimension line and ends in plan, sections, elevations, PDF and DWG/DXF; the number keeps its annotation ink. Colour edits the colour through a matching line style. Choosing a named style replaces the previous own colour, weight and pattern; later own values take precedence, just as on a line. Select a reference plane or setting-out point to use the same Line style list for its guide ink. Reference planes and setting-out points remain non-printing and stay out of PDF and CAD exports.

Measure, Tape and Dimension use the shared cursor catches at both ends, including loose line endpoints and an arc's Centre and Quadrant. Before the first end is placed, a direction inferred from a nearby point can catch an edge as Intersection; that catch keeps its link to the geometry. The preview and saved result use the caught points. Dimensions retain their link to the geometry they caught. From the first end, coloured inference guides help you stay on an axis; the guide names On Red axis, On Green axis or On Vertical where that direction is available in the drawing. Press an arrow to hold it, press the same arrow to release it or another arrow to replace it. A face keeps its Face cue when you pass automatic guides or other points. A held arrow lock takes priority; the object snap word clears when the end leaves that object. Camera eye and aim placement also catches nearby geometry; see Saving camera views.

In plan and 3D, Escape cancels the current draft and keeps the tool armed; press it again to return to Select. With no draft, one Escape returns to Select. An open dialog or popover closes first, except that a drag in progress above a popover (a slider, say) is cancelled before it, and a focused text field keeps Escape for itself.

In 3D, both ends of a measurement catch nearby model geometry, including loose line endpoints. The preview and saved measurement use those caught points. Camera eye and aim placement also catches nearby geometry; see Saving camera views.

In plan and 3D, Escape lands the picked dimension witnesses exactly like Enter, including a picked pair whose offset has not been clicked. The live next witness is left out. One Undo removes what landed. With no draft, one Escape returns to Select. An open dialog or popover closes first, except that a drag in progress above a popover (a slider, say) is cancelled before it, and a focused text field keeps Escape for itself.

Measure without drawing

Choose Measure beside Select at the top of the left rail, or find it in tool search. Click an edge, move off it and click to place a parallel dashed guide. Click a corner and the guide starts at that corner, even where it sits on another edge, such as a skirting's end on the end of its wall. Type an offset and press Enter to set it exactly. Starting from a point draws a guide in the direction you move; arrow keys lock its axis. Guides use the shared snaps in plan and 3D, including split view. Enter with no typed length or Escape leaves the current live span and keeps guides already placed. One Undo removes a placed guide. Press Escape again with no span to leave the tool. T stays Reference plane, which shares the tape engine.

Tap Ctrl (Option on a Mac) to measure a distance. Click two points, type the real length, such as 5000 mm, and press Enter. Choose Yes when asked to resize. Measure rescales the selected massing objects and imported drawings about the first point, or the active level’s with an empty selection. Taping a known length on an imported CAD drawing and typing the true one rescales the whole drawing. See Measuring. With a guide image selected, the typed length calibrates that guide directly. See Guide images.

Measure, Reference plane, setting-out points and lines and the structural grid work in a section, an elevation and a callout as well as a plan. Whatever you place in a drawing lands at the model point you pointed at. To move a reference plane there, arm Move and drag its dashed line: it slides across the drawing, and its end chevrons set where it runs.

To reach them

At the right of the Build toolbar, after the divider, choose Reference plane, Dimension, Spot level or Coordinate. The tools shown depend on the view. On a narrow window, the last of these tiles sit in the More tools menu at the end of the toolbar.

Automatic dimensions

A curved wall's automatic dimension measures its rise from the chord to the arc. Select the run to add a label prefix or suffix, hide it, or drag it out as a separate dimension that replaces the automatic run. The separate dimension follows changes to the wall's curve. Reference and Opening reference are available for straight wall runs only.

Open Display in the menu bar, then hover or click 2D to open its settings flyout. Under Annotations, switch on Automatic dimensions. The overall strings measure the connected building from outer face to outer face, including projecting wings and bays, on the level you are viewing. The switch belongs to that level, so another level can keep its own. Select a wall and the automatic strings whose witnesses reference it turn blue. Deselect it and they return to their drawing colour.

To dimension a distance

In a site plan, Dimension snaps to geometry from every building on the site.

In plan, click Dimension, pick the first witness and the second witness, then click to place the baseline offset. Keep clicking further witnesses to continue the chain on that baseline. Backspace takes back the last point you picked and keeps the chain going. Enter, Delete or a right-click finishes the current chain and keeps every clicked span (a typed number in the number field is edited by Backspace as usual). The point merely under the pointer is left out. After the first two points the chain keeps their direction, so later points are measured along it, and one undo takes back the whole chain. Drawn dimensions on linework behave the same way. The preview lines are teal in plan and 3D while you place the dimension. Preview labels use dark text on the light canvas and light text on the dark canvas so the numbers stay readable. The first-point preview follows a nearby wall direction, and the picked pair establishes the true span. Preview and finished dimensions use the same geometry and notation: metric numbers omit mm and m, while imperial dimensions retain feet and inches marks. Hovering a number highlights the whole dimension in blue with the Select pointer.

In a section, elevation or callout, Dimension places the same dimension you place in plan: pick the witnesses, then click to place the baseline offset, and keep clicking to continue the chain. It stays on that drawing and exports with it. On a clad wall the cladding's joints, panel edges and courses take the snap too: their ends, their midpoints and any point along them. A dimension placed on them stays attached to those joints, so it follows them when you change the cladding spacing or move the wall. Each end keeps its place in the run of joints, counted from the start of the wall, so after a spacing change it sits on the joint now at that place.

Pick a corner or an edge of a wall, column, stair, beam, railing, curtain wall, door, window, floor, ceiling, room, roof, mass, grid line, reference plane, wall part or furniture, or of a line, detail component or repeating detail drawn in the same view, or a corner or edge of the site boundary once you have drawn one, and the dimension attaches to it: move the element and the dimension follows. This is the same in plan, section, elevation and callout. Stair dimensions report the stair's size: use its Parameters to change the rise, going or width. Typing a value on the dimension does not resize the stair. Drag a witness grip to attach it to another element, releasing within a few pixels of it at any zoom, or drop it in empty space for a free point; dragging a free end back onto an element attaches it again, and each drag is one undo step. In a section, elevation or callout, a witness released on a level line (and clear of any corner or edge) attaches to that level: raise or lower the level and the end rides the line, keeping its place along it. A level has no outline in plan, so this is section, elevation and callout only. Re-link attaches an end to the element that stood where it was, never to a level line by height alone. The dimension and annotation switches in Display > 2D, reached by hovering or clicking the menu's 2D row, hide and show these as they do in plan.

If a measured element or joint disappears, its dimension keeps its last position and shows UNLINKED in annotation blue. Centre marks show the word too. The warning stays on sheets and exports. Right-click the dimension and choose Re-link after placing a replacement corner, edge or joint nearby. Undo restores the original association.

In 3D, select one object and the dimensions that locate it stand in the model, the same ones plan shows. Temporary dimensions on a selected mass end on the drawn outlines around it. Hiding or deleting a reference clears its temporary dimension. Click a value, type a distance and press Enter: the selected object moves until the dimension reads it, as one undo step. Escape closes the box without changing anything.

When a selected door, window, rooflight, item or placed component has dimensions on both sides of it, an EQ button sits between the pair, in plan, section, elevation and 3D. Click it and the object centres between the two bounds, so both sides read the same, as one undo step. A locked object says so and stays where it is. A rooflight's pair measures to the edges of the roof plane it sits on.

Select a wall and its dimensions to the walls beside it are typeable: type a new distance and the wall moves to it. The default reference is the outer face. An exterior wall is measured from its outer face to the outer face of the exterior wall opposite, so a 200 mm house wall set out at 6.5 m reads 6.5 m across the outside of the building. An interior partition is measured to the centre line. The centre line and both faces stay available as snap points while you draw and move.

A dimension you have placed lights up when the element it is attached to is selected: select a window and its string turns blue, in plan, section, elevation and callout alike, and in 3D. A dimension that starts on the face of a wall lights up for that wall and for the wall that meets it there. Click one of its values and type a distance. The selected element moves until that span reads it, the other end stays where it is, and the rest of the string follows, all as one undo step. A locating dimension attached to a door or window jamb slides the opening along its wall, including a diagonal wall. If the value would take it past a wall end or into a neighbouring opening, a message explains why and the opening stays where it was. In 3D the element slides along the dimension line. A dimension that runs along a selected wall, with its ends on the walls that meet it at each end, sets that wall's length by moving a neighbour: the end toward the wall's start stays and the wall at its end moves, whichever way the dimension was drawn, and if that wall is locked the one at the start moves instead. A wall inside a closed group moves with its group. A dimension from the wall's own end to the wall that meets it there, or from a selected group to the walls either side, stays a plain figure with the same reminder. A placed dimension never changes an object's width, height or length itself. A span between an object's own two ends is a plain figure. Hover it for the reminder: Change this size in Parameters or with its chevrons. Use Width, Height or Length in Parameters, or its canvas chevrons, to change the size; attached dimensions follow on the drawing. A locked element names its lock and stays put.

To annotate a level or a coordinate

In plan, click Spot level and click a point to annotate its level relative to the datum, or click Coordinate and click a point to annotate its grid coordinate.

In a section, an elevation or a callout window the same tools place on the view: Spot level reads the height of the point above the building's datum, the building's own offset included, and the radius, diameter, arc length, ordinate and angular dimensions are placed with the clicks you make there. A click on a corner or edge of the building attaches the dimension to it, so it follows when that element moves; a click that an arrow-key lock has moved off the corner stays a plain point. The arrow-key locks work in the view's own axes.

To draw a reference plane

Reference points and lines take part in plan selection boxes. Hold Ctrl and click one to add it, Shift to add or remove it, or Alt to remove it, keeping your other selected objects. A closed group or component selects as a whole; enter it first to select the reference inside it. The Eraser follows the same group and component boundary.

Click Reference plane and pick two points. A green dashed line extends 600 mm past each end, with the picked points kept as snap references. A displayed alignment guide pins the next point to that alignment; move clear of the guide to release it. Select it to set Start level, End level and their offsets, or choose Unconnected and a height. Select several reference planes and each control writes to all of them in one undo step; where they differ it reads Varies. A selected reference plane shows end chevrons in plan, section, elevation and callout views. In a section or elevation, drag an end along the drawn line to change its extent in that view; the model plane stays in place. In plan, drag one and only that end moves, snapping as you go, with the other end staying put, and one undo puts it back. In 3D it is a pale green rectangle with a dashed boundary. Plans within its vertical extent can use it for selection and snapping. In plan, hovering it turns it blue, and the pick area includes the overshoot.

In plan, tap Arrow Right for red or Arrow Left for green before the first point, after it or while drawing the reference plane. The guide follows the hovered start before you click, then the leg follows the held direction through the placed start. A nearby edge or point supplies its exact crossing or projection onto that axis. Away from a catch, the live leg ends at the pointer's perpendicular projection, stepping by the selected increment when Magnet is on. The guide stops at the leg's end, the length readout measures that leg, and the held lock wins over an object catch. A nearby point can reference its projection along the line, but the end stays on the locked axis. If it leaves the catch, the catch word and marker clear; the lock guide stays. Tap the other arrow to replace the lock, or the same arrow to release it. While you hover an edge, Arrow Down holds the direction perpendicular or parallel to it and Shift holds the inferred direction, before the first point or along the leg; the hint for those two keys appears only then, and letting go of Shift or tapping Arrow Down again releases it. See Axis locks.

The Massing toolbar has its own Dimension and Reference plane for working in 3D. There, the reference tool offsets a parallel guide from an edge or draws one from a point. Dimension works the same way as in plan and as a drawn dimension: pick two points, then click to place the dimension line. That click finishes the dimension and the tool is ready for a new first point, so there is no chain in 3D (chains are for plan, section and elevation). Backspace takes back the second point before you place it, and one undo takes the dimension back. Type the offset to set it exactly. Resting 3D annotations hide behind model geometry; selected annotations remain visible through it.

Dimensions and every other tool snap to the drawn corners and edges of roof accessories: chimneys, dormers, rooflights, vents, solar panels and downpipes.

A measurement you have placed in 3D can be edited: select it and a small square sits at each of its points. Drag one to move that point, which keeps snapping to real geometry as it goes.

A locked measurement stays selectable but draws no end grips; unlock it to drag its ends.

In Smart measurement, the cursor snaps to nearby corners, midpoints and edges while the lens keeps showing the object's report. Click to pin the caught point and its report.

The measurements also work in a section, an elevation and a callout window. They snap to that drawing's own cut edges and linework, read from the points you click on it, and a measurement placed there is kept at the model points those clicks stand for. Select a saved measurement to move, rotate, scale, mirror or copy it in the drawing, with a live preview. Its model points retain their depth behind the drawing, and attached ends stay on their model features.

The Measure menu on a narrow window

When the window is narrow enough for the compact bottom bar, that bar carries a Measure button with a caret beside it. The button arms whichever measurement you used last, and the caret opens the list: Distance, Angle, Area, Perimeter, Volume and Smart. Under a Floor plan heading the same menu holds the plan dimension modes: Linear dimension, Continuous dimension, Radius dimension, Diameter dimension, Centre mark, Chord dimension, Arc length, Angular dimension and Coordinate dimensions. Pick one and the menu closes with that tool armed; click the button again to leave it.