Doors, openings and windows

Doors, openings and windows all go into walls. Arm the tool, click the wall, and the hole is cut for you.

With a wall selected, click or drag a door or window on it and you have the door or window: it is selected alone and a drag moves it, not the wall. The same holds in a plan, a section, an elevation and a callout. Click the wall away from the door and you keep the wall. With several things selected, dragging a door or window still moves the whole selection. In a plan, a section, an elevation, a callout or 3D, a door or window you drag stays on its wall: it sits at the point on the wall nearest your pointer, however far from the wall the pointer goes, and past either end it stops flush with that end, or, where another wall joins at that end, against the face of the joining wall, so it never runs into it. One Undo puts it back. Release it over another wall and it moves into that wall instead.

Doors, openings and windows follow the wall under the pointer in plan, in 3D, and in a section, an elevation or a callout window. In a section or an elevation the preview is an outline of the opening's width and height across the wall's thickness; it is blue while it stands on a wall and red while no wall is under the pointer, and it goes when the pointer leaves the drawing. A window or door already in the wall does not stop the pointer finding the wall behind it. A catch shows its own word, such as Midpoint. Near a wall end, the preview moves inward to fit and reads Clamped; where another wall joins that end, it stops at the joining wall's face. The click places the opening where the preview stands. Following a wall without a catch shows no snap label.

Cut a section, an elevation or a callout through a window and its glass is drawn as one line on the centre of the pane, the same single line the plan draws, for every window type. A sliding or hung window shows one line for each sash the cut passes through. The same line goes into a PDF or DXF export of that view.

A door wider than its wall is refused with a message. Placing a door or window over another opening is refused too; hold Alt to force the placement. When openings overlap, the one edited most recently shows a red outline in plan and 3D, with one warning when the edit finishes. Move it clear to remove the outline. Undo and redo do not repeat the warning.

To place an opening on a wall inside a group or component, enter the group or component first. Its walls stay part of the whole while it is closed.

Select several windows, or several doors, and Parameters shows the same sections as for one: Frame, Sill, Panes, Shape and the rest. A setting they all share shows its value, one they differ on reads Varies, and a change goes to every one of them in a single undo step. Offset from level, under Position, is offered too: each window or door is measured from the level of its own wall, a value they differ on reads Varies, and typing one figure sets every one of them to that offset. The Documentation settings (Construction, Dimension to, the rough, masonry and finish opening sizes) and Follow curve work the same way, and Follow curve only changes the ones on a curved wall. Where each one sits along its wall (X and Y), its Mark and its Prefix are not offered while more than one is selected. Pick one of several kinds with the Show list when you select windows and doors together.

A window type from the library (Sash, Sliding, Bay and the rest) places an ordinary window with the same sections as any other, and only sets the starting values. Change the number of panes and the glazing bars are drawn in the model, plan and elevation for every window type. A sliding or sash window takes an arched or rounded head under Shape, and a bay or bow window takes a Sill.

For a window, select a pane in Openers, seen from outside, then tick Opener. Choose Top hung, Bottom hung, Left hung or Right hung. Untick Opener to make the selected pane fixed.

Reveal depth, under Position, sets how far a window's or a door's frame stands in from the wall's outside face, in millimetres. It reads Centred until you set it, and Centre frame in wall (or clearing the field) puts it back. The plan, the section, the elevation, the 3D model, the cill or door sill and the lining returns around the opening all follow it, and a reveal deeper than the wall allows is held at the deepest the wall leaves. A door is offered it when its plan draws a frame box (a hinged, double or french door), and you can set it before you place too, in the Parameters row for the armed tool.

For a round window, pick Circular window from the window type list before you place it, or select a window and choose Circle under Shape. A circular window has one size, Diameter; width and height stay equal whatever you edit, and the sill height stays where it was. It has a frame and glass like any other window, and a pane grid or an opener on a casement is available too. It is a fixed or casement window: choosing a sliding, sash, bay or bow window turns the circle back into an ordinary window. The wall is cut round in the model, section and elevation. In plan the window shows the width of the round cut at the plan's cut height, so a cut through its centre shows the full diameter and a cut near its top or bottom shows less. Its centre and four quadrant points can be snapped to, and Space flips it in or out like any other window. Save it as a type to reuse your diameter.

Show in 2D, under Face finishes, lets a door or window draw its frame, leaf and glass colours, and the same section carries the pattern and background controls as on a wall. Glass starts with a pale tint wherever you see it, in an elevation or in a section looking at a window. Glass that a section plane cuts through draws as a plain outline with no colour, on windows, doors, curtain walls, glass railings and rooflights alike. Windows and doors paint over the wall lines and patterns around their openings.

A door armed on the south wall of a room in plan, with its swing previewed and its Parameters row open.
A door hovering on a wall, with the typed distance from the wall start.

To place a door

  1. Click Door on the Build toolbar.
  2. In Parameters, choose the Door type, Width, Height, Facing (Front or Back), Hinge side (Left or Right) and Handle side (the handle always stands on the edge opposite the hinge, so choosing either sets both, in plan, in 3D and in elevation), the frame colour and the leaf colour, each with separate Outside and Inside rows.
  3. Click a wall.

On a narrow window, the Door, Opening and Window tiles can sit in the More tools menu at the end of the Build toolbar. Their keyboard shortcuts work the same.

Placement is Place once or Place multiple. A door stays armed by default, so you can drop several in a row. One Undo takes back the door you have just placed and leaves the tool armed; Escape puts it down. Windows work the same way. Click a frame or leaf colour swatch and the Library opens on its colours; choose one there, or press Cancel in the banner to leave it as it was. Auto returns a side to its default.

A door in an external wall gets a sill under it, out through the reveal, and a door in an internal wall gets none. Select a door and its Sill section shows what it has: Auto follows the wall and says which it picked, and On or Off sets it yourself when you want the other.

In plan, no door draws a line across its opening at the wall's inner face: an external door shows its frame, leaf, swing and sill, and the floor finish runs to the frame inside. The floor's outline follows the opening in to the door's own frame line as well, so it does not cross the opening at the inner face: a swing door's frame, or the pane or leaf line of a sliding, garage or pocket door. The room boundary stays on the wall face and its area is still measured there. An internal door leaves the floor on the wall line. A hinged, double or French door with Side lights switched on draws the door frame whole and each side light as one frame box the full depth of the door frame, from the reveal to the door jamb, with one glazing line down its centre, the way a curtain wall panel draws, in plan, in a callout, on a sheet and in a DWG or DXF. Side lights are added around the door, and the door itself must stay at least 300 mm wide (600 mm for a double or French door): a value for a side light, or a narrower opening, that would leave less is refused in the Parameters field, which keeps what you typed, says the door would be too narrow and names the most the side lights can be, in millimetres or in feet and inches to match the drawing. Nothing is clamped. A door saved before this with side lights over that limit keeps its data and draws as a plain door until you widen the opening or shorten the side lights. Flip Side turns the operation symbol, hinge side and swing together, to the other face of the wall. Swing doors show solid hinge arcs, sliding, pocket and barn doors show their slide direction, and bi-folds show joined thin leaves folding towards their hinge side, without pivot squares or a head track. Plan, PDF and DXF carry the same linework.

Barn doors have lined jambs, an unfilled closed leaf outline and a rail on the finished wall face. Flip Side changes the mounting face, and sections and elevations draw the leaf and rail on that same face, slid along the wall by the door's open amount, so a parked barn door leaves the opening clear. The leaf and rail stand clear of the outermost wall layer, including a cladding layer; decorative seam relief does not move this mounting datum. Pocket doors cut a real cassette cavity beside the opening in plan, section and 3D. The opening width stays unchanged. The closed leaf spans the opening; an open leaf parks in the cassette, and a section through the opening shows no leaf there. Linings stay at the doorway jambs, while framing clears the cassette. PDF and DXF use the same plan linework. Tap Space on a barn door, while placing it or with it selected, to change which side its leaf parks on. The same choice is the Rail row (Left or Right) in Parameters, before you place the door and on a placed one, and it shows what a Space tap chose. A pocket door warns about a wall only when that wall passes through its recess or its clear opening; a wall standing against the host beside the recess does not.

The Door type list has five groups in order: Internal (Internal door, Internal double doors, Internal bi-fold), External (External door, External double doors), Glazed (External French doors, Sliding patio doors, External bi-folds, External sliding door (3 pane)), Specialist (Pocket door, Barn door), then Garage (Sectional garage door, Roller garage door, Up-and-over garage door). A member-made type follows the presets in its family's group. External double doors are a pair of equal solid leaves in an 1810 by 2100 opening, with the sill of any external door drawn in plan and its threshold in section. Choose a garage type in this same list. New garage doors mount behind the opening on the inside face. In Parameters, expand Garage and choose Mount to fit behind the opening or in the reveal, on either face. Existing doors without a mount setting keep their in-reveal fit. Space or Shift+Space swaps the mounting face during placement or on a selected garage door, in one undo step. The placement preview shows the chosen garage door at its armed width and height before you click the wall. In plan, the overhead travel is a single dashed outline with no fill. Sheets, PDF and DXF show the same outline; the opening and its cut jambs stay solid. Sectional tracks use the ordering height plus 510 mm; the frame and guides stay in place as the curtain opens.

Choose External sliding door (3 pane) for overlapping glazed panes on separate tracks. In the placed door's Sliding section, set Panes (2-6), Tracks (1-3), Stack side (Left, Right or Centre) and which numbered panes are Fixed, counted from the left. One track cannot pass another pane; additional panes on the same track stop beside one another. Open slides moving panes towards their stack, while the plan keeps the closed layout with a direction arrow on each pane that travels. Frame depth sets the track enclosure; it is at least 120 mm where the wall allows and always fits between the wall faces. A door type carries its glazing. External bi-folds, Sliding patio doors and External sliding door (3 pane) come in as full-height glass, External French doors as glass over a short kick panel, and every other type as a plain solid leaf. Pick a different type on a placed door and its glazing follows.

Select a door or a window and each jamb gets two grips. The arrows on the jamb slide it along the wall; the second pair, standing off the wall face in plan and at the head corners in 3D, change its width. Drag one and that jamb goes to your pointer from the first move, with the other held, and it catches what the pointer is on within a few pixels at any zoom; a click on the grip, or a hand that wobbles a pixel or two, changes nothing. Hold Shift to grow both sides about the centre, or type a distance while you drag and press Enter. The ends of the wall, the openings either side and the door type’s width limit stop the drag, and when the width limit is what stopped it a message says so. If the door or window shares its type with others, resizing it moves it to a type of its own at the new size, and a message says so.

To pick a new host

Select a door or window, right-click and choose Pick New Host, then click the new wall in plan or 3D. The same element moves, keeping its mark, type and parameters, at its current height. The old wall closes and the new wall is cut. Selected openings on one wall move together, keeping their spacing; the first selected opening lands at the point you click. If any would not fit, nothing moves and the message says why. Escape cancels. One Undo restores the whole move. Enter a group or component before picking a wall inside it. Wall-hosted foundations, balconies and piers use the same command.

A door or window's plan tag and schedule row read its prefix followed by its mark, such as 00.D01. Open Documentation on a single door or window: the Prefix row shows the level's prefix (00. for the ground floor) as a placeholder. Type your own, such as GF-, to replace it for that element alone, or clear the field to return to the level's prefix. Numbering runs separately within each prefix, so the first door with GF- reads GF-D01 whatever the 00. doors hold, and doors and windows keep their own runs.

To cut an opening

Click Opening and click a wall: a frameless hole is cut. Its Parameters are Door type, Head (Rect, Rounded or Arch, the same three the door and window panels offer), Width and Height, with Arch height when the head is an arch.

To place a window

Click Window, then click a wall. Parameters holds Window type, Width, Height, Sill height, Facing (Front or Back), the frame colour (Outside and Inside rows, picked in the Library as for a door) and Placement. The Window type list has five groups in order: Casement (Casement, single; Casement, double; Top-hung), Sash (Sash; Single-hung sash), Fixed and sliding (Fixed light; Sliding window; Circular window), Bay and bow (Bay window; Bow window) and Specialist (Louvred). A window type you make yourself joins the group of its family, after the presets. While you place one, type its distance from the start of the wall, press Tab, type its centre height and press Enter.

A side-hung window shows its hinge in plan with a dashed swing arc and open-sash line, even when closed. These stay visible at both coarse and fine detail. In elevation and when seen beyond a section cut, the dashed triangle points to the hinge. Hinge left and right are named from outside; an inside view mirrors them, and Flip Side turns the plan indication with the window. Fixed panes have no opener mark.

When no per-pane openers are set, the window type supplies the triangles: a casement uses its selected hinge side, a French casement shows both leaves, an upward awning is top-hung, and a downward awning or hopper is bottom-hung. Sliding and vertically sliding windows have no hinged triangle. Setting per-pane openers overrides that operation, with any unspecified panes fixed.

To place at an exact position

With the pointer over a wall, type a number and press Enter. The prompt reads From start for a door or opening, and From start then Centre height for a window (Tab moves between them). An overlapping typed position is refused just like a placement made with the pointer.

To move by a placed dimension

On a straight wall, including one that runs diagonally, snap a placed dimension to a door or window jamb. Select the opening and its bound dimensions turn blue with its temporary dimensions. Click a value, type a distance and press Enter: the opening slides until that dimension reads the value, with the other end held fixed. This works in plan, section, elevation and callout, as one undo step. A dimension across the opening's own width or height is a plain figure: change the size in Parameters or with its size chevrons, and the attached dimension follows. A value that would take it beyond a wall end or into a neighbouring opening is refused with a message. See Dimensions and setting out.

What takes the click

Whatever is nearest under the pointer takes the click, and nothing behind it does. A wall that does not reach the storey you are working on, a wall inside a group or component you have not entered, and the end face of a wall are refused: nothing is placed and the wall behind is left alone. Clicking a wall that does not reach your storey says so and points you to the Levels tab at the top of the tray. A wall built on a lower level and topped at this one counts as being on this level, so you can place on it from here.

A fence, column, beam, slab, ceiling, stair or curtain wall standing in front of a wall takes the click in the same way, so a door or window will not reach through it. A gap between balusters or fence boards is not a hit, so the wall shows through there, and a ceiling seen from above counts as a surface like a slab. Dragging a door or window to a new place follows the same rule. The one exception is the armed Door tool, which places doors in a curtain wall's bays itself, so a curtain wall does not stop it; the Window tool, and a door or window being moved, are stopped by it like any other fence, column or slab.

Anything hidden, whether by its eye, its layer or phase, or a storey that is not drawn, never takes a click, and the click goes on to what is behind. Aligning elements, Splitting walls and Placing balconies work nearest-first too.

Under a roof

Windows in two walls that meet at a corner can be joined into a bay. Select both windows and click Join in the panel (it reads Unjoin once they are joined). Each window stays a whole frame, the wall is cut on past each frame to the corner, the cill runs to the mitre and one post, a frame wide, stands between the two. Move a frame more than about 250 mm from its corner and the wall closes up again.

When a wall's top follows a roof (Attach to roof, floor or ceiling… under Top), a door or window that crosses the roof line is cut to it. The frame and the glass are cut along the same underside the wall is, so a tall window in a gable wall gets a raked head that follows the slope and closes along it. This holds in 3D, in section and in elevation, and in the exports that draw from them. Linea tells you once, in a message, when a door or window comes to cross the roof, whether you place, move or resize it or draw, move or re-pitch the roof across it. A door or window that sits entirely above the roof line is not drawn, and the message says so. Nothing is deleted: lower it or raise the roof, or delete the roof, and the door or window is whole again. Opening a model that already has one stays quiet. The cut reaches every door and window the wall hosts: one with no frame (its outline in 3D stops at the roof line too), one filled with a type you made, and one in a copy of a component whose roof differs from the other copies, which is cut to its own copy's roof.

On a curved wall

Doors, openings and windows go into a curved wall the same way, in plan and in 3D. The door or window stands at the point you click on the curve and turns to follow it. It is a flat unit with a straight leaf and frame. The wall is cut square to the curve at that point, all the way through its thickness, so the two sides of the opening are parallel and the width you set is the width across them.

Switch on Follow curve in a door's or window's Position section and the frame, leaf or sash, glass and cill bend onto the wall's arc between the two jambs, at any radius the opening fits and whichever way the wall bulges. The width you set stays the width across the jambs, and the schedule row says so. A swing leaf is curved when shut and swings on its hinge as one piece, and a sliding leaf runs along the arc on its track. In plan the frame and leaf are drawn as arcs, and sections, 3D, DWG, DXF and PDF follow. Beside a straight wall the row is greyed out with a note, and a unit you move there keeps the setting and is drawn flat until it is back on a curve.

On a curved wall, distances along the wall are measured along the curve, as in the typed From start, and a door or window stops a little over half its width short of each end. A door or window remembers how far along the curve it stands, so it stays put when you save and reopen, however deep the curve, and a wall that is curved after the fact carries it along. Moving a door or window, nudging it with the arrow keys, and using Trim, Extend or Align all slide it along the curve. It shows in plan, section, elevation and 3D, in the door and window schedules, and in DWG and DXF exports, like any other.